2 Digit 99 Seconds Timer

  • Rajkumar Sharma
  • 15134
    Views
  • medium
  • Tested

99_SECONDS_TIMER_IMG

2 Digit Count Down Timer is a utility Count Down timer project for upto 99 seconds of countdown time.  This project can find many uses in your shack and home.  The relay output remains on during the Count Down period, allowing you to interface load or alarm that you want to keep it on for a certain amount of time (in seconds).

Specifications

  • Microcontroller based design for greater accuracy and control
  • Power supply input 12 VDC 200 mA
  • Two 0.5″ display segments to display time
  • 12V SPDT (Single Pole Double Throw) relay for alarm use
  • Single key start and dual key alarm time set function
  • Power and Relay-On LED indicator
  • Terminal connectors for connecting power supply input and relay output to the PCB
  • Onboard regulator for regulated supply to the kit
  • Crystal resonator based design for better accuracy
  • PCB dimensions 72 mm x 81 mm

This is a microcontroller based 2 Digit (99 Seconds) Count Down Timer.  This Count Down Timer is very easy to use and easy to configure.  This project can find a lot of application areas where you need a device to remain ON (or OFF) for a certain period of time (upto 99 Seconds).  Power to the circuit is applied at CN1 (12 VDC).  D1 provides the reverse polarity protection to this kit.  LED D2 confirms DC Power Supply to the board.  S1 and S2 displays Count Down time.  J3 provide an easy way of connecting external switches to this board.  LED D4 confirms the relay status.

Operating Instructions:

The setting up of countdown period and START Function for this kit is accomplished with the help of 3 tactile switches shown as SW1, SW2 and SW3 in the schematic and labeled as UP, DOWN and SET on the PCB respectively.

  1. Setting Time : The default value is shown on display S1 and S2 respectively. You can change this value by simply pressing the UP and DOWN key.
  2. Start : You can start the Count Down by pressing SET key. When the Count Down starts the relay is energized, indicated with the glow of LED D4. Once the Display (S1 and S2) reaches 0 the relay is de energized.

Schematic

99_SECONDS_TIMER_SCH

Parts List

PCB

Comments

  • Jayendra Buddh

    we want 99 min timer

    3 years ago
  • faiz

    operating instruction, can step 2 be relay de energized when count down start and how

    2 years ago
  • admin

    The relay is ON during the count down, so you can use NC (normal connected) or NO (normal open) connection of the relay, according to your needs.

    2 years ago
    • faiz

      thank you for the reply.i need time delay by using count down counter. relay will be off before starting count down then on. can i get asm file to make some change.best regards

      2 years ago
      • admin

        We are sorry, .asm code isn’t available at this moment.

        2 years ago
  • Rafiq

    Sir I made this circuit as per circuit diagram but it is not working properly not showing display properly so I need ur help to solve this problem

    10 months ago
    • admin

      Make sure you have wired the circuit as shown in schematic and verify your PIC is programmed and running.

      10 months ago
  • Kevin R Crutchfield

    can this module be used to drive 8″led digits?

    2 months ago
    • 7-Segment displays are directly driven from MCU pins. Current output on these pins is limited to 20-40mA, so to drive larger displays you will need some additional circuitry using transistors to control the segments.

      3 weeks ago

Leave a Reply to Electronics Lab Cancel reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.

RELATED PROJECTS

By continuing to use the site, you agree to the use of cookies. more info

The cookie settings on this website are set to "allow cookies" to give you the best browsing experience possible. If you continue to use this website without changing your cookie settings or you click "Accept" below then you are consenting to this.

Close