Motorcycle Universal Gear Indicator

A

Introduction

This is a new design for a universal gear indicator that can be fitted to any motorcycle as an aftermarket accessory. Its main advantage is that its operation depends entirely on the gear shift lever movement, instead of connecting to speedometer and tachometer sensors (found in expensive commercial devices), which are rarely available in older motorcycles. It consists of a main circuit including a 7‑segment LED indicator, two Hall sensors that are attached to the motorcycle frame, and a small magnet placed on the gear shift lever.

Image_1

The main circuit is based on an AVR ATTINY25/45/85 microcontroller, which reads the signals of the two Hall sensors and the neutral switch and outputs the current gear number to a 7‑segment LED indicator, through a 4026 counter/decoder.

At maximum output power there is significant heat produced by IC1 and for that reason we mounted it directly on the ground plane to achieve maximum heat radiation.

Schematic

Source Code

The source code is written in AVR-GCC (WinAVR) and can be programmed with the default fuses using an AVR programmer (default : ATTINY25 microcontroller and USBTiny programmer). Moreover, the constant TOP_GEAR 5 should be changed to 6 for six-gear motorbikes. Source code can be downloaded on the download section below.

PCB Design

The suggested implementation for the main circuit is a small size, double-sided PCB, with SMD packages for the microcontroller and the decoder ICs. The 7-segment LED is placed in a secondary PCB, connected vertically to the main one in a modular fashion (see pictures). Two PCBs for different Kingbright LED footprints (red and blue) are also provided.

Image_3

Parts List

R1 10 to 220 Ω ½W Depending on preferred LED brightness
R2, R3 10 ΚΩ ¼W
C1 220 μF / 35V Electrolytic capacitor
C2 100 nF MKT/polyester capacitor
MCU ATTINY25/45/85 Mouser Part 556-ATTINY25-20SU
COUNTER 4026 Mouser Part 595-CD4026BPWE4
IC1, IC2 Hall sensor Melexis US5881LUA
IC3 7805 5V Regulator TO-220
BLUE Kingbright 0.3″ Mouser part 604-SC03-11PBWA/A
RED Kingbright 0.3″ Mouser part 604-SC03-12EWA
JPx Pin connectors As shown in silkscreen and pictures

Possible improvement

In the current design, when the neutral switch is open (there is a gear on), there appears to be a very small current (< 0.5 mA) sinking through R3, due to the voltage difference between the neutral switch connection (TO_POWER-4) and the microcontroller. If the neutral indicator is of LED type (not a resistor bulb), there is a possibility that it stays dimmed, instead of being completely off. In that case, a small switching diode (1N4148) can nicely replace R3 (on the same PCB) in order to block this small incoming current when the neutral switch is open, as shown in the figure below :

Image_15

For a better insight in the above issue, the following script can be imported in Paul Falstad’s excellent circuit simulator:

http://www.falstad.com/circuit

$ 1 5.0E-6 10.20027730826997 62 5.0 50
R 192 96 192 48 0 0 40.0 5.0 0.0 0.0 0.5
R 512 96 512 48 0 0 40.0 12.0 0.0 0.0 0.5
r 192 96 192 176 0 10000.0
x 231 142 309 145 0 12 internal pullup
x 125 25 277 31 0 24 Gear Indicator
x 456 26 571 32 0 24 Motorcycle
M 192 176 96 176 0 2.0
x 65 157 118 160 0 12 AVR Input
w 192 176 192 256 0
162 512 96 512 160 1 2.1024259 1.0 0.0 0.0
r 512 160 512 256 0 470.0
d 512 320 512 400 1 0.805904783
x 413 388 499 391 0 12 protective diode
s 512 400 640 400 0 1 false
g 640 400 640 448 0
x 539 422 615 425 0 12 neutral switch
x 309 240 391 246 0 24 1N4148
x 132 377 269 380 0 12 in place of R3, and watch
d 304 256 400 256 1 0.805904783
r 304 336 400 336 0 10000.0
x 337 371 367 377 0 24 R3
S 192 320 272 320 0 1 false 0
w 192 256 192 320 0
w 304 256 272 256 0
w 272 256 272 304 0
w 304 336 272 336 0
w 400 256 400 304 0
w 400 304 448 304 0
w 400 336 400 304 0
w 448 304 512 304 0
w 512 304 512 320 0
w 512 304 512 256 0
x 131 359 276 362 0 12 flip switch to insert a diode
x 134 394 272 397 0 12 current drop to zero when
x 134 412 254 415 0 12 neutral switch is open

… or click here for direct Circuit Simulator Link
Contributed by Brett Walach

Photos

B

C

D

E

Connections

Image_8

Image_9

A successful circuit build will do a self-test when connected solely to 12V power (pins TO_POWER_1 and TO_POWER_2), by cycling through all digits on the 7-segment display (see video below). After the self-test, the current gear will be shown and can be changed by the shift lever movement. Note that a gear is changed when the magnet’s south pole is drawn away from the sensor (north pole will not work). Moreover, if a neutral gear is detected (from the neutral switch connected to TO_POWER_4), the display resets to zero (also acting as a self-calibrating feature if anything goes wrong). Finally, when the power is turned off, the last shown gear is stored in the MCU’s flash EEPROM and restored when the device is turned on again.

Image_10

The following video shows the initialization procedure of the gear indicator :

Self_Test

Sensor Cable

The following photos show the construction of the 4-wire sensors cable that is plugged to the TO_SENSORS connector. The visible sensor pin parts should be covered with plastic lacquer for protection as well.

Image_13

Image_14

 

After putting it all together the circuit is now operative and ready to be installed on the motorcycle. A video showing a simulation of gear shifting (by hand) is available below :

Circuit_Operation

Installation Photos

Here are some photos and videos from the installation on my Suzuki Intruder VS400

Image_16

Image_17

Image_18

Image_19

Image_20

 

Custom Housing

G

H

Image_5

 

Installation Videos

Installation1 – Gear shifting by hand

Installation2 Real gear shifting with engine on

Installation3 – Storing last gear in EEPROM

 

Thanks for reading !

Designed and built by Vassilis Papanikolaou © 2010

Please follow and like us:
Pin Share

PCB



Subscribe
Notify of
guest

68 Comments
Inline Feedbacks
View all comments
Sigit Yuliardi Cahyonawanggono

Any source code for cub type motorcycle ?

Jerry

What is the cost of the Universal Gear Indicator ?

ahmedzubair

Which vehicle do you need this for?

Dima

please tell me. put together your project, but I have no response to UP and Netral inputs. And the switching goes from 0 to 9. Tell me where I did something wrong

ahmedzubairAhmed

The cylinder case / housing seems impressive, how did you make it?

Madusha

Isn’t there a video making this?

RELATED PROJECTS

TOP PCB Companies