Jump to content
Electronics-Lab.com Community

Heeeeeeelp!!


Recommended Posts

Hi guys!
I am in mojor trouble and need some expert help!! :'(
Last week i was set a task of creating some equipment that would perform a simple task, so brain says simple task - simple to create (or so i thought!)- wrong!!!
Now guys let me just explain, i wouldn't usually take on a task like this, as i haven't done anything remotely electronic since i dropped the topic @ gcse for woodwork!! :-[ But when the guy who's asking me is the father of my future wife and i'm a young man oh to eager to impress, it becomes difficult for me to say no!! Now i have tried all sorts of avenues, i have been into Maplins Elctronics here in norwich and non of them had the knowlage needed appart from the manager who was to busy to see me, thought about going back to my lady's secondary school for advice untill i found out that she never got on with her teachers!! so gifted with a project that is now more about resourcefullness than knowlege i come to you!! Please help!

The project is:
to create a box that has a number of nobs and dials on it. the nobs serve the following purposes, two nobs that turn through six points, each point is numbered , on one the numbers start @ 2 and go up in multiples of 2 through to 12. then the second dial goes up in multiples of 15 (from 15-90). These numbers represent seconds of time that a light, that is placed above each dial, will stay on for. then a button placed underneath each dial to start the light for the selected amount of time. also a power on/off switch for the batteries powering the whole thing. i have to make five of these units.

PLLEEEEEEEASE HELP!!!

Link to comment
Share on other sites


heheheeh! looks like you're in a deep mess! How much time do you have. what kind of components can u use? do you have to begin from zero? I'm probably not the right person to help you with your project, but if you make your requirements more detailed and clear other people might be able to help you. relax and get organized....hahahaha. like the ad" sometimes is better to chew than talk Probably someone in here will know how to help you but you have to be more specific. just wait for the big heads to log in

Link to comment
Share on other sites

unfortunately I can't help you. but you could wait for a reply by the experts here. also you could subscribe to the piclist...www.piclist.com
browse their posts and if you don't find something relevant
send a mail at the address below
[email protected]
body subscribe piclist Your Real Name
body subscribe piclist


these are the sites of their archives
archive www.infosite.com/~jkeyzer/piclist/
archive www.iversoft.com/piclist/
archive (old) www.am.qub.ac.uk/world/lists/pic/
archive groups.yahoo.com/group/piclist1/

Link to comment
Share on other sites

The heart of your circuit can be a 555 timer. A resistor and cap determine the time, so you can have the switches determine which resistance is used. I have attached a link or a tutorial on a post somewhere in here. Use the search function for 555 and you should find it. You should be able to prototype the circuit on a bread board in one evening and complete the project by the next.

MP

Link to comment
Share on other sites


The heart of your circuit can be a 555 timer. A resistor and cap determine the time, so you can have the switches determine which resistance is used. I have attached a link or a tutorial on a post somewhere in here. Use the search function for 555 and you should find it. You should be able to prototype the circuit on a bread board in one evening and complete the project by the next.

MP

you are an absolute superstar!! ;D
Link to comment
Share on other sites

Look at this one too!
If you set the first one for 2 seconds then the incroments will be 2,4,6,8,10,12,14,16,18,20.
If you only use the 2 thru 12 settings You will have the first step of your request filled. As for the other step just change the value of C1 so it is a 15 second interval instead of 1 min. My guess would be between 47uF to 100uF.
(You must tie the unused outputs to ground because they will pick up stray signals and cause erratic operation and cause excessive power consumption.)

post-787-14279141588936_thumb.jpg

Link to comment
Share on other sites

All this advice i'm getting from from people is realy kind and generous and is realy very much apreciated. Thank you. ;D

but i think it's time to give up on me. As i have come to realise, i am well in above my head. All of these diagrams (which i'm sure, would be easy to understand, if i had an ounce of knowlage) are like rocket science in chinese brail, to me! :-[

I simply don't have the knowlage to make this thing work. and nothing less than someone explaining every little component,what it is & what to do with it would get me outa this mess. I Don't understand what the circuit diagrams mean. the squiggley lines and numbers -well lets's put it this way- if i found them anywhere else, i would think i had made first contact with the bourg!! :( (resistance is futile)

But everybodys efforts have been very much appreciated. But from a guy whos only knowlage of circuits was wiring a 9v battery to a light bulb in secondary school, i think that i may have to make a big slice of humble pie and go and explain to my lady's dad that i'm beat! :-[

And here was me hoping to turn my delorean into a replica of the BTTF time machine with flashing lights, time circuits, flux capacitors and things of the kind. well i think i may have to re-think that one. ???

thanks again
James ;D
(elec-dunce)
(no Doc Brown)

Link to comment
Share on other sites

now that sounds like a plan. ;D
now let me think, who do i know who could do that........umm....... how about......nahh....he's in jail......erm...... how about...... nope he's married......oooh.......i know!!!........now don't be stupid, you dumped her and didn't return her calls.........nope thats me, again, drawing a blank! :-\
this is when i realise that i've spent my life hanging around with useless people!!! : ::)

Link to comment
Share on other sites

  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
  • Create New...