Jump to content
Electronics-Lab.com Community

Build A Wooden Portable Speaker Box


Sherldonnnn

Recommended Posts

This is a sharing of  a portable speaker design project. Have you ever thought about designing and building your own portable speaker? A project like this is both easy and cheap if you source your parts wisely and have basic knowledge of electronics, soldering, and box construction. 

47616c003fe49883-0427151330.thumb.jpg.091cb793e70bcb480dc35f8b82d167a2.jpg

The first question you have to ask is, "What do you want this to do?" If you want 40 Hz bass extension, then you will have to design for it. If you want high SPL, again, you will have to select an amplifier and loudspeaker combination that can provide that. What did I want? I wanted a portable, battery-powered stereo speaker of moderately high fidelity. Bass extension was not a concern, but "punch" was. From this, a sealed enclosure was selected. 

Before building the version you see above, I prototyped the circuit on a breadboard with an enclosure made from a wooden quill box that I cut two holes in with a box cutter. The basic circuit diagram for this prototype was nothing more than connecting the audio to the amplifier and the amplifier to the speakers (well, provide the power too). For reference, the diagram is shown below.

(THIS IS NOT THE FINAL DESIGN, SCROLL DOWN FOR THE FINAL ITERATION)

0be35fa63358535c-schemeit-project1.png.bcb2602908b5f30bb1b218b630be19dd.png

The amplifier here is a 3W stereo IC-based audio amplifier that I ordered from a Chinese website(http://www.kynix.com/Detail/647721/PAM8403.html). It cost me $2. For $2, I figured I would give it a try.

Pretty simple, right? Just connect it together the logical way. Now that I've shown how it went together, maybe I should share the parts list of the V1 electronics. There will be more components added in a minute.

Parts List V1

  • Stereo 3W Audio Amplifier (PAM8403) x1
  • 3.7V 1860 Li-Ion Battery & Battery Holder x1
  • 1/8" Stereo Jack (or whatever you would like to use for the input) x1
  • SPST (single pull, single throw) Switch x1
  • Loudspeaker x2 (preferably 4 Ohm, I used 8 Ohm)

I prototyped this circuit on a breadboard just to convince myself that what I had designed would actually work, and was surprised at the quality of the amplifier. There was distortion at higher volumes, but this was a result of the amplifier wanting 5V and the battery only capable of supplying 3.7V. I highly recommend this amplifier for all low power applications. 

Being as excited as I was, I quickly shoved the electronics in the quill box. I added a mute switch along the way, which was just a momentary switch connected to ground and a pin on the amplifier. It looked like this.

8dfabd4704c40410-0330151940.thumb.jpg.dc9d34e0d7c1fead4d246534c8c4680c.jpg

Opening the box and exposing my hurried soldering and poor wire management... Some of the connections are twisted and taped together since I planned on transplanting it into a proper enclosure. 

564f6cf918f5cc14-0330151941.thumb.jpg.897fdb725aab364aa42c1179fe45ee34.jpg

Notice the clean sock.

So, I built the skeleton of the enclosure that same night out of aspen, a soft wood that you would not normally build an enclosure out of, but it was what I had on hand and is very forgiving when I make mistakes. 

e59782b721ab56c3-0330152249.thumb.jpg.21efe89f1fbd7f2784525a36d8293787.jpg

You can use whatever material you like to construct the box, but a common choice is MDF. MDF is made from sawdust and glue, with the mixture being compressed into the boards you buy at the store. The product is perfect for this purpose since the material is not of uniform density and does not sympathetically vibrate at frequencies we are concerned about. I chose the aspen, which you have already seen, for the sides and red oak for the front and back faces.

I have tools available on this site for enclosure design, and they work great for calculating necessary box volume on a project like this. My box was build from the output of the tool and then the dimensions increased ever so slightly to lower the system resonance at the expense of system Q. I lost some of the "punch" in the bass I mentioned I was after, but I gained a deeper reach.

Then I glued the rear face on the box.

1ee2c6a1f1285236-0401151409.thumb.jpg.bd0f972f916a9ab7072fa6e1f3b540bf.jpg

e98ac60ff530cc0e-0401151518a.thumb.jpg.2320990bf34a6a7d37be119256c69b7f.jpg

Designing as I went, I decided to add an "X" brace to the top of the enclosure to help minimize the low frequency energy lost to the panel. It was made from strips of 1/2" plywood and glued to the inside.

ba3c70b1f98df66b-0401151625.thumb.jpg.a41dc39ab262aa3590867daec1cc4d92.jpg

Using a forstner bit, I cut two holes for the speakers on the front panel and one on the side for the audio jack and power switch. It would have been easier to cut the hole for the steel panel prior to gluing the box together, but you live and learn.

0d71f40981d129d7-0403151340a.thumb.jpg.d835bdb0d08965e1b762918e0b2cff99.jpg

9261e9a935a60414-0403151536.thumb.jpg.825be020e155bd2f37a2bde65d44eb2d.jpg

 

Electronics V2

To mitigate the distortion at high volumes, the 3.7V 18650 was swapped for a rechargeable 9V. Since the amplifier only accepts voltages up to 5.5V, a 5V regulator was necessary. A filtering capacitor was also added to the circuit even though there is minimal noise from a battery power source. 

This was when the issue of charging the 9V became a problem. I had originally purchased a micro-USB charging module that would have charged the 18650, but the module's fully charged voltage was 4.7V. The regulator needs altleast 5V to let current pass. 

So, I had to design a charger myself. Googling a circuit to charge a 9V yielded a number of possibilities, but for simplicity I chose to go with a single 20 Ohm resistor to limit the current into the battery. There is no protection for the battery this way, but I included an LED that will turn off when the battery is fully charged. This charger also charges very slowly (approximately 14 hours for a full charge), which minimizes the risk of me leaving it on the charger too long. You will need any 9V wall-wart to supply power. The regulator and charging circuit are shown below. 

815ff47f6309e19c-0422151613a.thumb.jpg.fcb16facc774496915033bd20a3a91b4.jpg

0070f9b94b57f38e-0422151613.thumb.jpg.e767a293ce7b5fd7c496a232ed6871f4.jpg

I then drilled two holes in an 1/8" steel plate and mounted the switch and audio jack to it. After wiring it all together, it just needed to be test one final time and mounted in the box. 

25edc0de08a38e8d-0410151810.thumb.jpg.04459fe93a8159ccc82b92effc57433d.jpg

Parts List V2

  • Stereo 3W Audio Amplifier (PAM8403) x1
  • 9V Rechargeable Battery
  • 1/8" Stereo Jack (or whatever you would like to use for the input) x1
  • SPST (single pull, single throw) Switch x1
  • 5V Regulator
  • 10 uFarad Capacitor
  • 20 Ohm resistor for 9V Charger
  • Barrel Jack for charger
  • Loudspeaker x2 (preferably 4 Ohm, I used 8 Ohm)

Final Assembly

374994a0acab8120-0422151649.thumb.jpg.21a582c3028ba77673c3d5b8c6efeb86.jpg

47616c003fe49883-0427151330.thumb.jpg.091cb793e70bcb480dc35f8b82d167a2.jpg

94f0cfe164fe1fdf-0427151417.thumb.jpg.fe78ede24d3692bfdcc4a7a25a151a3b.jpg

 

Now it is done! Do you want to have a try? Then go on with it! If you have any question, please leave a comment below~Thanks for reading.

 

Link to comment
Share on other sites


The speaker drivers look tiny, 2 inches or 3 inches in diameter like a cheap clock radio? No bass.

The PAM8403 amplifier IC produces 3 Whats with high distortion into a 4 ohm speaker per channel or 2 Watts at less but still audible distortion when the supply is 5V.

Have you heard the Bose little Bluetooth mono speaker? It sounds great and costs $200.00.

Why is your speaker stereo? The speakers are too close together for stereo. If you made a mono speaker with the same size enclosure then the speaker driver can be larger for better bass.

 

 

Link to comment
Share on other sites

  • 1 year later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
  • Create New...