nogueiraat Posted April 24, 2021 Report Share Posted April 24, 2021 I have electronic devices from 1990 and I know that these devices that have not been used for a long time cause faults and depolarization in the electrolytic capacitors, is it necessary to use these devices in the interval of 1x a month to preserve the electrolytic capacitors from failing due to disuse? are used electrolytic capacitors manufactured since 1990 and assembled in electronic circuit Quote Link to comment Share on other sites More sharing options...
HarryA Posted April 24, 2021 Report Share Posted April 24, 2021 I would think that using the devices, as you suggest, once a month would be a good idea. Also you could do a quick test on the capacitors if you have not used the device in some time. I often check the capacitor with a multi-meter using the ohmmeter range without disconnecting it. The reading will start low then rise as the capacitor charges indicates a good capacitor. If this fails I disconnect one lead and try again. If the reading stays low it could be shorted. If no capacitance it will often just show a high reading. see: https://www.wikihow.com/Test-a-Capacitor If you doing many capacitors perhaps a tester would be worth the monies: https://www.amazon.com/HiLetgo-Multifunctional-Capacitor-component-Backlight/dp/B01MYU0QI3/ref=sr_1_10?dchild=1&keywords=tester+electrolytic+capacitor+tester&qid=1619267945&sr=8-10 Quote Link to comment Share on other sites More sharing options...
nogueiraat Posted April 25, 2021 Author Report Share Posted April 25, 2021 necessary to use these devices in the interval of 1x a month to preserve the electrolytic capacitors from failing due to disuse? Quote Link to comment Share on other sites More sharing options...
HarryA Posted April 25, 2021 Report Share Posted April 25, 2021 Modern aluminum electrolytic capacitors have longer shelf lives then the old ones, usually around 2 years. Perhaps powering up old equipment a couple of times a year would be sufficient. Once a month is perhaps unnecessary. I have never found any good information on that subject. I have an old audio amplifier I power up a couple of times a year. I keep thinking someday I will use it - perhaps. Quote Link to comment Share on other sites More sharing options...
nogueiraat Posted April 25, 2021 Author Report Share Posted April 25, 2021 using the electronic device 1x in the year will have chemical reactions inside it leak, explode depolarize lose capacitance? the electrolytic capacitors in my case are mounted in electronic circuit are used and made in 1990 did you say 2 years of use they die or two years of storage? Quote Link to comment Share on other sites More sharing options...
HarryA Posted April 26, 2021 Report Share Posted April 26, 2021 Folks that restore old radios say do not power them up until replacing the capacitors. It is difficult to find information on failing due to disuse. Wikipedia has some information related to storage. See "Performance after storage" here: https://en.wikipedia.org/wiki/Electrolytic_capacitor#Operational_characteristics Years ago, okay many years ago when I was in HS, I used to repair radios and bw televisions. I repaired a radio that a mouse had chewed into a wax coated capacitor. Quote Link to comment Share on other sites More sharing options...
nogueiraat Posted April 26, 2021 Author Report Share Posted April 26, 2021 Whenever I store electronic devices, will I have to change all the electrolytic capacitors before reconnecting them? Quote Link to comment Share on other sites More sharing options...
HarryA Posted April 27, 2021 Report Share Posted April 27, 2021 I take it if one is not going to use something often one should power in up say once a year or so. The question is if one is not going to use something often enough to keep the electrolytic capacitors refreshed why keep it at all? I keep my old audio amplifier thinking I will use but I may never use it. Quote Link to comment Share on other sites More sharing options...
nogueiraat Posted April 30, 2021 Author Report Share Posted April 30, 2021 Do you have any concrete information for the storage time of electrolytic capacitors in electronic circuits and manufactured since 1990? 1 month, 1 year, 2 years etc I don't mean new and spare electrolytic capacitors? Quote Link to comment Share on other sites More sharing options...
HarryA Posted May 1, 2021 Report Share Posted May 1, 2021 No, the information is not readily available. From page 29 section 7.3.2 "Storage condition" in: http://www.epcos.de/blob/185386/download/4/pdf-generaltechnicalinformation.pdf "If not otherwise specified, our aluminum electrolytic capacitors can be stored voltage-free at above stated conditions (from +5°Cto+35°C, relative humidity≤75%) for at least two years; capacitors of the SIKOREL series can be stored for as long as 15 years under these conditions. Within these storage periods the capacitors can be operated at their rated voltage directly after being taken out of storage. It is recommended to mount the capacitors in the application within one year of delivery in order to prevent any problems with solder ability of capacitors on PC " There is some information at: https://en.wikipedia.org/wiki/Electrolytic_capacitor#Reliability_(failure_rate) Quote Link to comment Share on other sites More sharing options...
nogueiraat Posted May 1, 2021 Author Report Share Posted May 1, 2021 my room the temperature varies 31-33º the humidity varies 55-70% this epcos information valid for other electrolytic capacitor manufacturers? in the 1990s were electrolytic capacitors or another type of capacitor used? 17669 1 Quote Link to comment Share on other sites More sharing options...
nogueiraat Posted May 4, 2021 Author Report Share Posted May 4, 2021 Quote Link to comment Share on other sites More sharing options...
Guy Shemesh Posted May 7, 2021 Report Share Posted May 7, 2021 The epcos informaion is only valid for epcos 🙂 Electrolytic capacitors from 1990 is generally something to beware of. They contain liquid or gel electrolyte which basically dries out over time. from 1990 up to now its 30+ years, I'd say that failure is quite certain. Moreover, the failure can damage other areas in your circuit. I would just replace these.. Good luck Guy Quote Link to comment Share on other sites More sharing options...
nogueiraat Posted May 8, 2021 Author Report Share Posted May 8, 2021 are electrolytic capacitors since 1990 different from today's electrolytic capacitors? does not use them before two years work in preserving them from disuse? Quote Link to comment Share on other sites More sharing options...
Guy Shemesh Posted May 9, 2021 Report Share Posted May 9, 2021 As I said, they dry out.. Quote Link to comment Share on other sites More sharing options...
nogueiraat Posted May 22, 2021 Author Report Share Posted May 22, 2021 Does this 2-year rule apply to any electrolytic capacitor manufacturer? Quote Link to comment Share on other sites More sharing options...
Sekemiat KE Posted February 8, 2022 Report Share Posted February 8, 2022 The best way is before using a long time disused electronic device you need to change the electrolytic capacitors. It is good to avoid risks accompanied with using a faulty capacitor. Quote Link to comment Share on other sites More sharing options...
Jully Jean Posted May 16, 2022 Report Share Posted May 16, 2022 they dry out.. smash karts Quote Link to comment Share on other sites More sharing options...
BD Electronics Posted June 7, 2022 Report Share Posted June 7, 2022 On 4/24/2021 at 12:52 PM, nogueiraat said: I have electronic devices from 1990 and I know that these devices that have not been used for a long time cause faults and depolarization in the electrolytic capacitors, is it necessary to use these devices in the interval of 1x a month to preserve the electrolytic capacitors from failing due to disuse? are used electrolytic capacitors manufactured since 1990 and assembled in electronic circuit You can frequently check the capacitor with an ohmmeter range multi-meter without unplugging it. A good capacitor will have a low initial reading that rises as the capacitor charges. If this doesn't work, I'll unplug one of the wires and try again. It may be shorted if the reading remains low. It will typically only indicate a high reading if there is no capacitance. If you like to find more details check out:https://bde-ltd.com/blog/ Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.