Recent content by moeinglory

Search Forums New Posts
  1. moeinglory

    power with line wire enter the wall switch and out going and there is no neutral

    OK anyway thank you. for your time and help.
  2. moeinglory

    power with line wire enter the wall switch and out going and there is no neutral

    ok so if you want control 1000w lighting? what you do? i used one of this (livolo) switches before, its really 2 wire and don not need neutral(or negative) and picture is for 2 gang key. 4 point is line in. out 1 out 2 and com(ground) or( earth) that no need to connect to switch work. i try...
  3. moeinglory

    power with line wire enter the wall switch and out going and there is no neutral

    ok tanx. but what i do with neutral absence, and i dont think it be dangrous as you say. please check out this link and tell me what you think they do? http://www.livolo.com.tr/products6.asp Installation is as same as normal light switch, so does not require Negative line; Replace...
  4. moeinglory

    power with line wire enter the wall switch and out going and there is no neutral

    no its not just for my wireless i have 555 ic and decode ic and relay. for all of tis i almost need 200 - 300 mA. of course right now !!!
  5. moeinglory

    power with line wire enter the wall switch and out going and there is no neutral

    I design before this system with MOSFET and OpAmp and relay but just for 500 to 1000watt max. its something like 2 wire electronic switch (LIVOLO) if you have seen them before, but i have 2200watt load. and that circuit was complicates really. so i have acquaintance with this types of circuit...
  6. moeinglory

    power with line wire enter the wall switch and out going and there is no neutral

    Look. i need the circuit give me 5 volt and 300 mA when the load is ON. i use this circuit to keep my system alive. my wireless receiver, so i can send the command to turn the pump off.
  7. moeinglory

    power with line wire enter the wall switch and out going and there is no neutral

    Ok, of course i have full responsiblity of circuit and all consequence is just with and for me!! and if you think triac is better so i can use it instead of relay.
  8. moeinglory

    power with line wire enter the wall switch and out going and there is no neutral

    and excuse me but in your fanrunon diagram. your diode don not convert AC voltage to DC? we need AC voltage on load.
  9. moeinglory

    power with line wire enter the wall switch and out going and there is no neutral

    OK! so the triac has no rule to providing current and voltage when the load is ON its just a switch like a relay but with low current. is that right? and..... yesss, confirmed . we discussing about the load ON times. when its OFF any power supply will be work. we need the power supply for...
  10. moeinglory

    power with line wire enter the wall switch and out going and there is no neutral

    Can you explain what is the triac rule exactly in your circuit diagram please? i mean can i use relay instead of triac? tanx a lot
  11. moeinglory

    power with line wire enter the wall switch and out going and there is no neutral

    Yes . i don not use mechanical switch any more. and power circuit with load current when the load is ON. and in OFF time its simple to run it. if need i can use relay to ON-OFF load.
  12. moeinglory

    power with line wire enter the wall switch and out going and there is no neutral

    Here is the block diagram. i havent schematic because i dont know what i must do!!!!!
  13. moeinglory

    power with line wire enter the wall switch and out going and there is no neutral

    how i must programming the micro.? it should on off triac so fast? how we must earn power? with interrupt ?? by triac?
  14. moeinglory

    power with line wire enter the wall switch and out going and there is no neutral

    yes yes. i know that. thats the reason i told i use a switching power while the load is OFF to running the pump (turn it on) then for turning it OFF using your method to keep the power of circuit to be able recieve command to off the pump,
  15. moeinglory

    power with line wire enter the wall switch and out going and there is no neutral

    yes look i have an ordinary RF transmitter and in switch i have receiver and a relay but if i use triac i dont need relay any more, my RF receiver need 5 volt and about 200 mA current power supply and i hope i can use your method to power my circuit. and on-off my switch and water pump remotely...
See more
Top