Search results

  1. M

    RCA F19207BC (CRT TV) shuts itself off even after new HOT install.

    Sorry again for long response time had some family problems. I did the test out of circuit with a brand-new multimeter too
  2. M

    RCA F19207BC (CRT TV) shuts itself off even after new HOT install.

    Sorry for the late ness again life got to me but glad you're feeling better! Anywho did the test on both sides. Left pin was 82.6ohms and right was 0.21!
  3. M

    RCA F19207BC (CRT TV) shuts itself off even after new HOT install.

    Checking that big heatsink with the vertical output and removing the support bracket shows this. Need a bit of cleaning with alcohol
  4. M

    RCA F19207BC (CRT TV) shuts itself off even after new HOT install.

    I apologize for the late reply. I was feeling under the weather as of late but I did find the chassis number and it's CTC185A
  5. M

    RCA F19207BC (CRT TV) shuts itself off even after new HOT install.

    Ok, so doing that from emmiter to base gave me Zero ohms in circuit for some reason. And the voltage in test 2 was 194v and 200v. Each probe on the horizontal plug measured different...
  6. M

    RCA F19207BC (CRT TV) shuts itself off even after new HOT install.

    I have this RCA tv and since the horizontal and vertical cables are separate on the yoke the vertical works works fine but as soon as the horizontal is plugged in the TV immediately shuts itself off and I just replaced the HOT too. The only test I did on the yoke was seek of there was...
  7. M

    Sansui TDC2075A (CRT TV) has no power or standby lights.

    Im taking precautions with properly discharging PSU components. Even worked on the one in a smaller CRT before but this one has a DVD player and VCR so the board is much more complex and Im unsure to what part could be bad
  8. M

    Sansui TDC2075A (CRT TV) has no power or standby lights.

    I don't have a way of getting an ESR meter for my 200v 680uf but I also tested the voltage coming out of it while plugged in and It read about 160v
  9. M

    Sansui TDC2075A (CRT TV) has no power or standby lights.

    Tried looking online and I followed guides with sets having similar issues and they don't really help all too much unless you can point me to one. And I tested the large 200v cap just like in this video using the ohms settings since my meter doesn't have a capacitance mode. I am aware of the...
  10. M

    Sansui TDC2075A (CRT TV) has no power or standby lights.

    Checked all fuses, replaced a bad resistor and MOSFET and still dead. I think it's a power supply issue but unsure WHAT issue it has. I removed and tested the large black cap with my digital meter and it seemed to be fine gaining charge and doing as good cap would from the videos I watched. Now...
  11. M

    Reparing dead Sansui TDC2075A

    (bump and update) Finally got them in and replaced the bad resistor on the Sansui board but still no power coming out of the switch-mode transformer
  12. M

    Panasonic PV-M1323-A 13 VHOLD issue

    I don't have a VHS tape unfortunately but I tried a few other devices like my NES and old camcorder and they have the same instable picture issue and white line moving up the screen. Plus if you look at the blank blue screen which is the tuner's input and the black screen which is the AV input...
  13. M

    Panasonic PV-M1323-A 13 VHOLD issue

    My Panasonic PV-M1323 WORKS but has this vertical issue going on and no way to adjust it that I know of. I tore it down to see is someone maybe knows which cap could be causing it or something else. Video: https://i.imgur.com/WvzBYgV.mp4 PCB images: https://imgur.com/gallery/mlwtsx2
  14. M

    Reparing dead Sansui TDC2075A

    UPDATE TWO Did the testing like you said and in the areas probed https://imgur.com/gallery/KJ8NtZO it read -62 and 62 depending on the spot and the part you marked with a yellow arrow coming out from and the box read ZERO. Note again my hand slipped and I blew that resistor but I had done the...
  15. M

    Reparing dead Sansui TDC2075A

    Forgive me for being slow and having a late response but I REALLY appreciate your research into this and the detail. I just want to be sure here... I should reassemble the TV set and test the voltage coming out of the power supply shown with the yellow arrow, and the likely culprits are the...
  16. M

    Reparing dead Sansui TDC2075A

    I own a digital meter but I'm not 100% sure how I should be testing the caps resistors I included more detailed images of the PCB of the main board with power cable and the flyback and that I know of there's only one glass fuse which I checked to be fine https://imgur.com/gallery/CI1QHTp
  17. M

    Reparing dead Sansui TDC2075A

    I already removed the main board and discharged it but I don't know what can be causing it to have no power. No LED, no VCR and no DVD power. Below are links to images of it. I already tested the power button https://imgur.com/gallery/hiO9vHl https://imgur.com/gallery/xy9lpA1
Top