Search results

  1. Maglatron

    ethical hack

    to ADMIN please close this thread! thanks
  2. Maglatron

    ethical hack

    I want to use my hackrf to scan for a pager on a frequency assuming that I do not know the frequency that the pager is on, any help guys? thanks in advance!
  3. Maglatron

    PWM on 12volt winch?

    thanks Mr Minder how do I contact? do I just go through the contact us page and put in an email?
  4. Maglatron

    PWM on 12volt winch?

    so I'm set on the ac motor with VDF control! any that can be recommended please? as a set? as in motor and controller together please?
  5. Maglatron

    Hi, I want somewhere to buy a set of two gears at a 3:1 ratio i.e. 60:20 teeth with a centre hole of 15mm, any ideas?

    found what I needed on ebay!
  6. Maglatron

    Hi, I want somewhere to buy a set of two gears at a 3:1 ratio i.e. 60:20 teeth with a centre hole of 15mm, any ideas?

    Thanks Mr Bertus the gears will be made of carbon steel so I think that the power will be handled fine! just need to work out how to buy gears with matching pressure angle, diametrical pitch and module, for the gears to mesh!
  7. Maglatron

    Hi, I want somewhere to buy a set of two gears at a 3:1 ratio i.e. 60:20 teeth with a centre hole of 15mm, any ideas?

    so I found this site but struggling with it with pressure angle,, diametrical pitch and module, for the gears to mesh, any help please guys!?! thanks in advance! https://www.mcmaster.com/products/gears/component~gear/system-of-measurement~metric/shaft-diameter~15-mm/
  8. Maglatron

    Hi, I want somewhere to buy a set of two gears at a 3:1 ratio i.e. 60:20 teeth with a centre hole of 15mm, any ideas?

    Hi, I want somewhere to buy a set of two gears at a 3:1 ratio i.e. 60:20 teeth with a centre hole of 15mm, any ideas?
  9. Maglatron

    help with IR2110 chips

    been out of action for a bit hoping to get back on with the project soon i.e. finish the custom made inverter board from easyeda and finish the controller board with the (50Hz toggling signal, the ESC, and the screen with the voltage sensor and current sensor)!! and get the wheel moving and...
  10. Maglatron

    Comedy Thread

    why don't polar bears where socks? because they have bear feet!
  11. Maglatron

    help with IR2110 chips

    those spotting scopes are quite cool with the non-image inverting technology! and the nitrogen for the misting of the scopes!
  12. Maglatron

    help with IR2110 chips

    the situation is pretty FUBARE but thanks anyhow hah... beyond all reasonable explanation!
  13. Maglatron

    help with IR2110 chips

    sessions are on hold for a bit! back soon
  14. Maglatron

    help with IR2110 chips

    going to make a start on the board, that drives the inverter controls, the screen that displays the voltage and current form the machine, and also incorporates the ESC and they turn on with the double press of button for the activation of these three functions! getting there!
  15. Maglatron

    help with IR2110 chips

    so done the inverter board now just have to put on the connectors!
  16. Maglatron

    help with IR2110 chips

    so made a start on the new inverter; by not planning correctly, I didn't leave enough space for the a pin on two resistors to fit with the heatsinks, so going to get the Dremel out tomorrow and make minor modification to the heatsinks should be fine! the resistors and caps go on tomorrow too...
  17. Maglatron

    help with IR2110 chips

    will take photos soon! the boards look good!
  18. Maglatron

    help with IR2110 chips

    the boards have arrived along with the MOSFET's have arrived the caps too can't wait to get cracking and solder up he parts! p-g!
  19. Maglatron

    Sallen Key Low Pass Filter, bandpass filter

    I will take photos soon!
  20. Maglatron

    Sallen Key Low Pass Filter, bandpass filter

    finished another column on the spectrum analyser !! that's 5 ,10 to got
Top