Register
Log In
Join
Join the Community
Register
Log In
Main Menu
Home
Articles
Forums
Tools
Downloads
Datasheets
Register
Log In
Search...
Home
What's new
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Latest activity
Search Forums
New Posts
What's new
New posts
New showcase items
New showcase comments
New resources
Latest activity
R
rainyliveshere
replied to the thread
Suitable replacement for a large Siemens capacitor in an old IBM XT power supply
.
what voltage do you measure across the new 220 uF / 400 V capacitor while the PSU is switched on?
Oct 27, 2026
davenn
replied to the thread
Compass 320 magnum metal detector where plugs go
.
photos mite help people help you
Oct 25, 2026
B
Bobmac
posted the thread
Compass 320 magnum metal detector where plugs go
in
Datasheets, Manuals and Component Identification
.
Looking where and which male connector connects to male pins? One board has 6 pins but connector that was removed only has 3 female...
Oct 24, 2026
davenn
reacted to
rainyliveshere's post
in the thread
Technogym PCB component identification
with
Like
.
PC 11-13 look like surface-mount multilayer ceramic capacitors though I cannot say anything about the values.
Oct 24, 2026
davenn
reacted to
danadak's post
in the thread
Tek 2235A Scope - Lost Vertical after cap replacement
with
Like
.
Did you do power supply V checks, including AC line current draw to see if its in spec ? Does scope have power off resistance checks...
Oct 24, 2026
davenn
reacted to
Sparkystuff's post
in the thread
Tek 2235A Scope - Lost Vertical after cap replacement
with
Like
.
Thank you for responding. I checked the suspicious diode which showed it was not shorted, and it's forward voltage drop was correct and...
Oct 24, 2026
davenn
reacted to
danadak's post
in the thread
Tek 2235A Scope - Lost Vertical after cap replacement
with
Like
.
Dirty trigger channel connection switch ? Or any of the trigger switches, like mode and polarity, trigger pots ..... Use gentle force...
Oct 24, 2026
davenn
reacted to
Harald Kapp's post
in the thread
Step-down board In: 3.7v out: 2v
with
Like
.
What is your current requirement? I suppose with a 400 mAh battery you will need only a few mA, right? In that case you may want to...
Oct 24, 2026
R
rainyliveshere
replied to the thread
Step-down board In: 3.7v out: 2v
.
One thing to consider is the TPS62740 from Texas Instruments. It supports a 2.2–5.5 V input and an adjustable output from 1.8 to 3.3 V...
Oct 24, 2026
Delta Prime
replied to the thread
Tek 2235A Scope - Lost Vertical after cap replacement
.
Yes.
Oct 24, 2026
S
Sparkystuff
replied to the thread
Tek 2235A Scope - Lost Vertical after cap replacement
.
Thanks for the tips, I will see if it helps. Start simple, right? I have some Deoxit
Oct 24, 2026
P
Pervil
posted the thread
Step-down board In: 3.7v out: 2v
in
General Electronics Discussion
.
Hello, I am looking for a miniature step-down (buck) converter with maximum dimensions of 5mm (height) x 15mm (width) x 30mm (depth)...
Oct 24, 2026
D
danadak
replied to the thread
Tek 2235A Scope - Lost Vertical after cap replacement
.
Dirty trigger channel connection switch ? Or any of the trigger switches, like mode and polarity, trigger pots ..... Use gentle force...
Oct 23, 2026
S
Sparkystuff
replied to the thread
Tek 2235A Scope - Lost Vertical after cap replacement
.
Thank you for responding. I checked the suspicious diode which showed it was not shorted, and it's forward voltage drop was correct and...
Oct 23, 2026
D
danadak
replied to the thread
Tek 2235A Scope - Lost Vertical after cap replacement
.
Did you do power supply V checks, including AC line current draw to see if its in spec ? Does scope have power off resistance checks...
Oct 23, 2026
Home
What's new
Top
Continue to site
QUOTE OF
THE DAY
“
”
-