Search results

  1. Maglatron

    help with IR2110 chips

    now this sorry for all the quotes I'm just trying to determine if this is this: also included pic of back side of the board!! I do PCB layouts for pay. And I do the routing mainly by hand. So much more than 5 mins. Yes, they are called protoboard. I know them since the 1970ies. That also was...
  2. Maglatron

    help with IR2110 chips

    But it's okay in my situation? I suppose there is only one way to find out I could try and cut down the wire lengths to a minimum gut tells me it will be absolutely fine!
  3. Maglatron

    help with IR2110 chips

    so the "guy" on the other forum says was a waste of time.... but if you have read this couple of lines ... you also could imagine that your effort for the past days ... was the same. I´ve claerly written that a breadboard will not work. The used strip board is nothing better than a breadboard...
  4. Maglatron

    help with IR2110 chips

    there is space for sinks (slim sinks)!, can't see it being a problem! But I take what you say onboard, and will try to make the cables as short as possible. But BTW I did over compensate with the long wires because you can always trim back wire than putting it back on! Is 50Hz considered "high"...
  5. Maglatron

    help with IR2110 chips

    Finished!!!
  6. Maglatron

    help with IR2110 chips

    finished pics soon
  7. Maglatron

    help with IR2110 chips

    thanking you!! PROGRESS MUHAHAHAHAHAAAAA so I.ve made a start on the new inverter! have pics when done nearly finished the inverter! photos soon almost finished! Moderators note: compacting thread
  8. Maglatron

    help with IR2110 chips

    is this correct??
  9. Maglatron

    help with IR2110 chips

    I don't get it can I get some help! where do I put my decoupling caps? in mine pins 3 and 9 are not connected I think mine is most similar to the first one! do I just put them between pin 3 to GND. On pin 9 of mine it's only 5volt!! what should I do!!?? no decoupling caps shown on this...
  10. Maglatron

    help with IR2110 chips

    thanks Mr bertus!!
  11. Maglatron

    help with IR2110 chips

    trying to find out about decoupling capacitor in the data sheet https://www.infineon.com/dgdl/Infineon-IR2110-DataSheet-v01_00-EN.pdf?fileId=5546d462533600a4015355c80333167e
  12. Maglatron

    help with IR2110 chips

    ok cool because the Arduino both accepts and broadcast 5volt on the signal pins!! if broadcasting is the correct terminology :)
  13. Maglatron

    help with IR2110 chips

    like in the image in post 762 for the VDD the power for the Arduino and the signal logic? just to clarify and make sure! thanks
  14. Maglatron

    help with IR2110 chips

    thanks and is the 5volt source from the LM7805 okay?
  15. Maglatron

    help with IR2110 chips

    is it a good idea to put in decoupling 100nf caps over the vcc and ground BTW?
  16. Maglatron

    help with IR2110 chips

    THANK YOU jees that guy couldn't give me a strait answer, because in the sim it doesn't work if the, VDD is 5v and the signal is 3.3v. only VDD 5v and signal 5v or VDD 3.3 and signal 3.3 would this work having the LM7805 to drive the VDD and the Arduino and have the Arduino give out 5v for the...
  17. Maglatron

    help with IR2110 chips

    but let me say you guys have helped me no end and my loyalties lie here, just sayin
  18. Maglatron

    help with IR2110 chips

    yep I'm going to get inductance meter when I get paid also the coils are near identical I'm now using edaboards too a guy on there said "some points: 1) if the supply of the logic chip (that generates the signal) is 3.3V ... then the signal itself will always be less! 2) to me it seems the V_IH...
  19. Maglatron

    help with IR2110 chips

    so how do you hook it into the IR2110 inverter circuit? thanks
  20. Maglatron

    help with IR2110 chips

    cool that is good
Top