Search results

  1. W

    Need help troubleshooting control board

    he was doing a great job .i was not able to give results because he actually did not ask me to test anything if you read the posts .I would think with someone with a lack of knowledge in this field like me that a basic test would suffice to start with .If he spoke a little more clearly would...
  2. W

    Need help troubleshooting control board

    Can anyone else on here help me out to test this board.?
  3. W

    Need help troubleshooting control board

    Are there any test points on this board?Only voltage i see so far is the 120 volts input
  4. W

    Need help troubleshooting control board

    Are you still around DR Edd ?
  5. W

    Need help troubleshooting control board

    Yes the only thing the motor is responsible for is turning the rim clamp assembly for 1 speed the 2nd speed and reverse in order to change the tires.Yes it is only controlled by the right foot pedal and the 3 micro switches .Motor is connected with a v belt to a transmission which turns the...
  6. W

    Need help troubleshooting control board

    Here is a bad picture of the switch setup.The switch on the left is for reverse,the switch on the right bottom is for low speed and when foot pedal is depressed further hits the top switch combined with bottom one for higher rpm speed .Also picture is the rim clamp holder which the motor turns...
  7. W

    Need help troubleshooting control board

    The other 8 pin IC is 431A1H GZ34 The 4 pin isolator is V4378 F817d That RT2 varistor number is 14d511k (the one i tested says OL) can i resolder that back on the board? The thermistor i replaced.The old one was NTC 33 The new one is B57891mo333j000 NTC 33kohm 4300k
  8. W

    Need help troubleshooting control board

    The varistor reads OL
  9. W

    Need help troubleshooting control board

    The ID for that IC is R1013AP13 VAA 1333G
  10. W

    Need help troubleshooting control board

    My friend i think what you are asking is way above my skillset .To test that low voltage which is using pin 8 IC do i use pin 1 and 8 to test?
  11. W

    Need help troubleshooting control board

    If anyone can help me to test live voltages on this board would be great and how to check relay.I have 120 volt input here in Canada but can run a 220 volts if i have to will run another feed.This tire machine requires a 1 or preferably 2 speed and reversible motor.This machine is only for my...
  12. W

    Need help troubleshooting control board

    Ok will hook it to power and then hopefully you can give me pointers of where to measure voltages and what they should be .If you need better or closer up pics let me know
  13. W

    Need help troubleshooting control board

    I sent the Fiel company in France asking them a few questions and about a schematic of the board but there is no reply .There is little or no info anywhere on this board.They show a picture of the board and a pdf but thats about it
  14. W

    Need help troubleshooting control board

    No signs of any of that
  15. W

    Need help troubleshooting control board

    I checked online video how to test rectifier . I think it is ok. tested .456 on each leg and when pos/neg reversed tested OL
  16. W

    Need help troubleshooting control board

    Not certain how decent it is lol
  17. W

    Need help troubleshooting control board

    yes have multimeter
  18. W

    Need help troubleshooting control board

    Well i sent them info for a quote and here is the reply Hello, Thank you for contacting Rockwell Automation/Lektronix. As a result of their acquisition by Rockwell Automation, Lektronix will no longer be able to support the repair and/or supply of new or refurbished product within certain...
  19. W

    Need help troubleshooting control board

    more pics
  20. W

    Need help troubleshooting control board

    Hi everyone . I recently purchased a tire changing machine that came with an engine that was not working. It is an elprom engine and the control board is a Fiel 1007-01 .I took the cover off the control board and discovered that one of the 4 large capacitors had burned through it's solder...
Top