Search results

  1. 73's de Edd

    Charger fuse on the output side burned

    Sir gica69 . . . . . . You're only showing bits and pieces of that unit so any chance that this is the unit, with my seeing the little release lever and the Green status LED. https://westbuy.ro/storage/media/1400_products_img.jpg With the time accumulated internal dust and deteris . . . . ...
  2. 73's de Edd

    Part identification help?

    Sir Nonsheep . . . . It is an on-board battery. Not sure of its chemical makeup nor its output voltage being 1.2 or 3V with the latter being MOST likely. Why not take ohmmeter in hand, set to its lowest ohms scale and probe the corner hex brass spacers , at the gold flashed pad between them...
  3. 73's de Edd

    Burnt resistor’s value for MAS830L multimeter

    Sir Jarasmus . . . . . Initially I had no information or pics back when I first checked in. Now let me fill you in with my ensuing observations. I was wanting a pic of the extreme right two meter plug in terminals of the three, to confirm if center was ground and the far right was the 10A plug...
  4. 73's de Edd

    Burnt resistor’s value for MAS830L multimeter

    It’s weird that its parallel mate didn’t also toast down to the same fate ? I am also suspicioning it to be a decimal15 ohm unit. Is that unit auto ranging or do you have to purposefully switch settings to and probably have to swap one meter lead plug in position . . . .when measuring HIGH...
  5. 73's de Edd

    Need help with drum module hiss and clicks

    Sir Radon . . . . . My dealings with your situation was back in circa 1958 with an accompaniment sound effects electronics unit that a solo musician could use. At that time it was all first generation transistors with NO I.C.'s yet being on the scene. It had 3 sections just like yours does . ...
  6. 73's de Edd

    Gtech K9 handheld

    Sir wearyhacker . . . . . In getting on with re-referencing, see if this is being the correct Geeeeeeeeetech K9 SOOOOOPER Suckah . . .Then how about levering out this unit shown just below, that is associated with where the units thumb activated power switch is. Pry out from its very top end...
  7. 73's de Edd

    Hoover Vacuum Cleaner Brush Roller Stopped Spinning

    How about some more related info. . . . since you seem to have just skipped over past queries. Did you find either of the possible referenced circuit boards, being mounted in the unit ? Also, the pig tail fuse that either of them incorporate ?
  8. 73's de Edd

    Radiogram record player very faint sound

    I would be just fine with that Garrard SP25 choice.
  9. 73's de Edd

    Radiogram record player very faint sound

    I see several larger shielded wires thru the supplied photos but what I was looking for was a very fine gauge pair that would be run from the base of your turntable and up an thru the tone arm to terminate at the two plug in connections that are associated with you changing cartridge heads...
  10. 73's de Edd

    Hoover Vacuum Cleaner Brush Roller Stopped Spinning

    Just an update ordered a new sensor switch off eBay, did some testing with my multi meter and I think it's that that's gone. Design wise, one would expect a normally off position until the little nub is pushed in . . . . since you mention no lever being on your selected replacement . . . . . to...
  11. 73's de Edd

    Hoover Vacuum Cleaner Brush Roller Stopped Spinning

    If so then, do you know that there are ALSO normally open units ?
  12. 73's de Edd

    Radiogram record player very faint sound

    ASSUREDLY . . . .you ended up with their connections reversed, if touching the cartridge with finger / flesh results in amplified HUMMMMMM.
  13. 73's de Edd

    Hoover Vacuum Cleaner Brush Roller Stopped Spinning

    The reference does not have the lever, unless the one used in your unit ALSO does not use a lever. PLUS there are both normally closed . . .OR . . .normally closed switch actions options.
  14. 73's de Edd

    Radiogram record player very faint sound

    If the two wires that you reinstalled were very fine gauge wires ( in order to be able to flex VERY easily) . . . . I believe that you reinstalled them in transposed positions from the way that they had been installed at assembly time at the factory.
  15. 73's de Edd

    This is silly, but I cannot for the life of me figure out how to remove a footswitch

    I don't believe that the REQUIRED DEGREE of rotational torque attainable by youse guys use of the mini longitudinal keying slots in the control /switch shaft . . . . could even START to accomplish the initially required loosening up. In considering . . . . . that there is being no key...
  16. 73's de Edd

    Radiogram record player very faint sound

    When I rub my finger it does scratch and buzz very loudly. The large scratch reproduction was being exactly what was hoped for BUT the accompanying loud BUZZ / HUM was NOT expected . . .that sounds like the cartridge shell is not grounded and is picking up inter room radiated AC power wiring...
  17. 73's de Edd

    This is silly, but I cannot for the life of me figure out how to remove a footswitch

    Our most ESTEEMED . . . Martaine (yep, ALL 2005 of 'em) . . . sez . . . . You may need to use tweezers or something to go in each side of the jack from the top. You can see small rectangular openings either side. Those longitudinal slots . . . . what looks like micro Woodruff key slots . . . ...
  18. 73's de Edd

    This is silly, but I cannot for the life of me figure out how to remove a footswitch

    Thanks for any help! Why 'soitanly ! Here's your $100 of sheltered trade secret special information The problem is that I cannot for the life of me figure out if there is even a tool available for screwing this nut that is jammed in about a 1-2mm space between a circuit board and front panel...
  19. 73's de Edd

    Radiogram record player very faint sound

    Sir Zee Jay Ess . . . . 3 observations here Also, It has two removable styluses. One for 78's and another for 33's and 45's. The needle in the stylus that plays 33's and 45's broke so I am using the stylus meant for 78's on playing the records. I do not have any 78's but it does play the...
  20. 73's de Edd

    Need help with a Proton 619 TV problem. Ticking clock sound...

    99% of ticking sounds are a result of the PSU in shutdown mode if that was the case . . . . .when I turn it on, the picture and audio are still fine . . .would not be possible, with either an inoperative /or/ surging in and out power supply. If you are not experiencing the tic-tic . . . . . . ...
View older results
Top