Search results

Search Forums New Posts
  1. bertus

    In search of data sheet for an old Sansui tape deck chip MSA806

    Hello, Is it this deck? https://www.hifiengine.com/manual_library/sansui/sc-3300.shtml Bertus
  2. bertus

    Site originated Spam.

    Hello, I have removed the post as spam. It is possible that the post initiated a notification before I deleted the post. There was indeed some of the text changed to a link in the post, also seen as hidden spam. Bertus
  3. bertus

    Site originated Spam.

    Hello, Is it real spam or a notification from the thread? The forum system uses your email adress to sent you notifications, if you have enabled it. You should not receive mails when to notification is turned off. Bertus
  4. bertus

    Power window limit switch bypass

    Hello, Perhaps you could better ask it on a Mercedes automotive forum: https://mbworld.org/forums/ https://www.benzworld.org/forums/ https://www.forum-mercedes.com/ Bertus
  5. bertus

    Help with identification!

    Hello, The led you show is not an SMD version. An SMD 0603 would look like the ones in this google image search: bi color led 0603 Bertus
  6. bertus

    Folkscanomy: Ham and Amateur Radio on the internet archive

    Hello, Here are a lot of books and aticles on Ham radio related subjects: https://archive.org/details/folkscanomy_hamradio?and[]=languageSorter%3A%22English%22 bertus
  7. bertus

    Power connector - looks like a B on its side

    Hello, Does it look like the plug on this picture: https://www.ebay.co.uk/itm/352084969760 Bertus
  8. bertus

    Please help me Identify this part, thanks!

    Hello, The large blobls are for holding the part. You are right about one of them being connected to a track. It is for shielding, as the holder is made of metal that can be seen as a shield for noise. Bertus
  9. bertus

    Please help me Identify this part, thanks!

    Hello, As I said, the schematic came from the AP200. I assume a similar part is used in your system. As you can see in the schematic, the ground connections are common for left and right. The VR601 is only a location on the PCB. Bertus
  10. bertus

    Please help me Identify this part, thanks!

    Hello, Does the keyboard also have an other number? The celvanio is not found on this page: https://www.synthxl.com/manufacturers/casio/ There seem to be a lot of models: casio celvanio In the AP200 manual, I see it is a stereo potmeter with a common gound: Bertus
  11. bertus

    Comedy Thread

    Thanks cmartinez AAC
  12. bertus

    Electronics Boffins needed

    Hello, As the used relay is a latching relays. a short pulse would be enough to activate. The coil takes about 150 mA at 5 Volts, so it will dissipate 0.75 Watt. Bertus
  13. bertus

    Comedy Thread

    Thanks pushkar1 AAC
  14. bertus

    Electronics Boffins needed

    Hello, Here is what @Harald Kapp and @Bluejets implemented: Bertus
  15. bertus

    Micro USB cable

    Hello, As @Martaine2005 said, use a image search. I always use this: https://www.google.com/advanced_image_search? Bertus
  16. bertus

    Multimeter issue

    Hello, You are measuring in series with the load. In the 10 Amp range the resistance of the current sensing resistor is much lower as the 200 mA range. It sounds there is something wrong in the 200 mA range. It could be the sensing resistor or a switch issue. Bertus
  17. bertus

    Multimeter issue

    Hello, I see the meter has only three ampere settings: In the 200 μA range, it will be out of range. In the 200 mA range, it should show 21.1 mA. In the 10 Amp range, it will show 0. Bertus
  18. bertus

    Multimeter issue

    Hello, The make or brand is UNI-T. Wich version is it, as the flash covers the version? It looks like a UT131B: https://ttds.nl/shop/digitale-multimeter-250v-20mohm-uni-t Can you confirm? Bertus
  19. bertus

    Ball Magazine Stop Correctly

    Hello, You could place 5 magnets in the disk (with the 5 holes) and a hall sensor to detect the position. The hall sensor signal could be used to control the "hold" signal. Bertus
  20. bertus

    Burning PIC16F54s with the TL866

    Hello, Changed the title. Why do you want to use the programmer? There are pickit programmres special for the pics. https://pic-microcontroller.com/pickit-3-pinout-connection-diagram/ https://pic-microcontroller.com/pickit-3-supported-devices/#:~:text=Supported Devices To read complete...
Top