Search results

  1. gughanath

    Alarm

    hehe, no you explained it well :). I am not an electronic genius, but you definitly are, you just saved my life. Thanks a loooooooooooooooooooooooooooooooooooooooot!! ;D
  2. gughanath

    Alarm

    Why is it neccessary to add those extra capacitors?
  3. gughanath

    Alarm

    sorry, here is the circuit.
  4. gughanath

    Alarm

    I have a vibration sensing alarm circuit here. I want to build in a switch, which should act like a reset switch. It should stop the buzzer from sounding, the LED from emitting light and decharge the capacitor. I tried many time but couldnt find the right place to place the switch. The fist...
  5. gughanath

    Mechanics

    A block of mass m = 2.30 kg slides down a 30.0
  6. gughanath

    Electricity

    hey, sorry about the late reply. YES, you are right, this disagram is actually really bad. But still, the answers are correct. I realised what mistake I did too. Thanks for your help!
  7. gughanath

    Electricity

    This question is giving me a headache, I just dont get the right answer. Please explain how I could solve this problem!! R = 36 OHMS Find the current in the 36 ohms resistor. Find the p.d. between a and b.
  8. gughanath

    Jubilee Clips

    I am going to attach a bike alarm to the bike using a jubilee clips. Is this a good idea? Are the adjustable around the frame? Does anyone have any other alternative suggestions? If the jubille clips are a good idea, are they available in plastic coated form?
  9. gughanath

    Waterproof??

    hey. good idea but it is neccessary for em to have the holes on the front side of the case (the side that the user faces the alarm usually) due to aesthetics. Is there any other way to stop water rain destroying the electronics without having the holes behind the case?
  10. gughanath

    Waterproof??

    :-\I have made a case for my bike alarm out of ABS. I have drilled holes to allow sound from the buzzer to come out. Now, the problem is, if it rains, my alarm will get damaged because the water would flow through the holes into the circuit. The ABS is waterproof already, but how can I prevent...
  11. gughanath

    Potential divider

    Hey. Thanx people for your help. Now I undertand eveything! ;D ;D ;D ;D ;D
  12. gughanath

    Potential divider

    This is a simple potential divider...The battery supply is 12V...The voltage accross the 200 ohm resistor is 8V...and the voltage across the 100 ohm resistor is 4V...shouldnt the resistor with the greater resistance have the lower Voltage...i dont undertand this?...please help
  13. gughanath

    Tlit switch

    basically a vibration switch is like a tilt switch, it has two pins and a mercury ball. The ball sits on top of one pin, when the switch is tilted (by a very small angle), the ball makes contact with both pins, completing the circuit. I asked my teacher and said that a vibration switch does act...
  14. gughanath

    Tlit switch

    And how does a Vibration switch work. Say it is a normally open vibration switch, does it return to its normal position simultaneously?
  15. gughanath

    Tlit switch

    oh ok....in your opinion, do u think that a vibration sensor would be more suitable for a bike alarm and this circuit than a tilt switch? If you dont mind, could you also explain how a vibration sensor works?
  16. gughanath

    Tlit switch

    hey,,,,thank you very much for da circuit...but there still is a problem...when I trigger the tilt switch, the alarm does reset itself after a while, but then it starts again for some reason? How do I solve this problem?by the way, in my circuit simulation, I am using the tilt switch as a normal...
  17. gughanath

    Tlit switch

    Hey..sorry the circuit above is messed up...da correct circuit is attached to this message...i cant replace the push-to-make switch with a tilt switch (which basically acts like a normal switch on/off) because when the tilt switch makes contact and complets the circuit, it needs to break contact...
  18. gughanath

    Tlit switch

    hey everone....i have a circuit here....i need to know how to replace the push-to-make-switch with a tilt switch, so I could use this circuit as a bike alarm??....please help...i really need HELP!!!!!!!! Please download the picture of the circuit attached to this message, look at the circuit and...
Top