Transistor tester

[mozikluv1]

??? am very much interested in building this transistor tester project of which the author i believe is randy linscott as you have presented. however, before i do so, i would like to clear up some doubts,
1. is IC4027 a dual JK master/slave flip flop w/set-reset?
2. where can i find the datasheet for this ic
3. is pin 1 & 2 open or not used?
4. is the output of the 555 (pin 3) connected to pin 12 of the 4027?
thank you in advance for whatever info you can give me.

Project Link: http://www.electronics-lab.com/projects/test/008/index.html

 

[mixos1]

1. Right! CD4027 is a CMOS Dual J-K Master-Slave Flip-Flop with Set-Reset capability
2. Datasheet download: cd4027b.pdf (408 kb)
3. Pin 1 & 2 are not used.
4. Yes

 

[mozikluv1]

??? thanx for the datasheet you sent. however a good friend also sent me datasheet on this chip made by fairchild semi. CD4027BC. the one you sent was CD4027B by texas inst. i have seen both internal circuitry and each one differs. the BC type use single inverters while the B type uses 2 series inverters. is this output critical to the sensitivity of the tester? which one do you recommend. again thanx!

 

[mixos1]

If you look at the pinout of each circuit you will notice that they are the same. Also the internal circuit it's the same.

View attachment 35050

 

[mozikluv1]

;Dthanx my friend, will let u know of the result!

 

[mozikluv1]

to mixos: i now have all the parts of the transistor tester project, but my problem is installing the cmos device without damaging it. i know its sensitive sto static energy. is there a simple way of installing it? ???

 

[mixos1]

The best way to hanlde electrostaticly sensitive devices is to supply your work bench with an antistatic mat which is connected to the ground. Also you must discharge yourself. For that reason use a conductive wrist connected to ground. There are special Antistatic Work Surface Kits and equipment like below:

But in case you what to handle electrostatic sensitive devices occasionaly and don't want to buy any special equipment, follow the rules below :

1. Don't handle CMOS circuits directly.
2. Avoid touching metal leads and other circuit areas when handling devices with CMOS parts.
3. Discharge your hands by touching a fount.
4. Try to handle CMOS from it's case.
5. Use a pincer to install the cmos, which you have connected to the ground.

If you follow these rules you can install it succesfully. Keep in mind that cmos can be installed succesfully without following any of these rules if you are lucky, but these rules will reduce the chance to damage it.

 

[mozikluv1]

sorry if i sound too naive about handling cmos.
1. how about if i have to align the pins to the socket, what do i use to straighten the pin. someone advise that i can use a long nose plier provide the plier is insulated and i dont touch the pin directly, also they say i dont have to worry about electrostatic energy here in the Philippines bcoz we have humid weather here. Is this true?
2. my workbench is made of wood and also have wooden floor.
3. do i have the plier attach to a ground?
your reply would be highly appreciated. thaanx in advance!

 

[mixos1]

mozikluv you and your questions are always welcome !

1. Attach the plier to the ground for some seconds to discharge it. Handle it from an insulated grasp. Then align the pins without fear. If you want to feel more secure attach the plier to the ground via a cable, but i think it's not quite necesarely. The weather also helps if it's humid to have less atmoshpere charges.

2. I don't know about wood, but it's surelly better than having a moquette or carpet ;D !!

3. See -> 1

 

[Electronicslady1]

Hello I'm new to this site and I'm interested in building the Transistor tester and looking at the circuit diagram could you please tell me if pins 11,16,3,9,13 of IC 4020 are connected to anything or are the just left open.

Thank you for your help.

 

[mixos1]

Hello Electronicslady.
Welcome to Electronics-Lab community

Pins 10,11,16 connect together and to the rest of the circuit.
Pins 3-9,13 (3,4,5,6,7,8,9,13) connect together and to the rest of the circuit.

 

[mozikluv1]

hi,

i hve finished the transistor tester after a long delay and ''I HIGHLY RECOMMEND THIS PROJECT FOR ALL ELECTRONIC HOBBYIST" 8) 8) 8)

thanx to this site.

 

[kev1959electronics1]

Hi there can you please tell me if diodes D1 to D4 are connected directly to pin 15 via R3 exactly in the way shown in the diagram as I have tried it this way and I am unable to get this project to work please help as all I managed to do was FRY the 4027 Ic when it was connected this way :'(

 

[mozikluv1]

hi,

try to check your foil layout, there might be some short or there is a mistake in making the layout. also you might have damage the CMOS flip flop or its defective. remember that is static sensitive device.

 

[kev1959electronics1]

Hello there and thankyou very much for the reply to my question but can you please confirm that the diodes D1 to D4 are connected to pin 15 via the R3 resistor exactly as shown in the schematic diagram

 

[kev1959electronics1]

[Hello there and thankyou very much for the reply to my question but can you please confirm that the diodes D1 to D4 are connected to pin 15 via the R3 resistor exactly as shown in the schematic diagram can anyone help resolve this question ? as I am up the creek without a paddle becuase the diagram does not look right somehow I need to know the answer to my question before I can attempt to biuld this project ???

 

[mixos1]

This is right.. Go ahead.. build it and post your comments. Be carefull when you build it...

 

[Electronicslady1]

Hello Electronicslady.
Welcome to Electronics-Lab community

Pins 10,11,16 connect together and to the rest of the circuit.
Pins 3-9,13 (3,4,5,6,7,8,9,13) connect together and to the rest of the circuit.

Hello again I'm still trying to build this circuit and still not getting anywhere and I keep trying to get it to work but I think I've got the pinouts wrong because I'm only getting one led to light and that's lit all the time but does not flash.
This is what I've tried now I've got pins 3 to 9 and 13 of the IC 4027 all connected together and onto the neg rail and I've got pins 10 and 11 and 16 all connected to the plus rail.

I would be very pleased for any help that you can give me about this circuit as I'm new to this site and I've not yet managed to get this one to work so far.

Thank you
from Jennifer

 

[mixos1]

I suggest you to visit the author's site here:

http://home.maine.rr.com/randylinscott/

and email him with your questions.

The transistor tester is here:
http://home.maine.rr.com/randylinscott/nov97.htm

Don't forget to post the results and what caused the problem!