Search results

  1. narkeleptk

    Newbie - attempting to repair Ford circuit board

    You'd be surprised... I once didn't notice the date was about 2 years old on a thread at another forum and replied with some help, Turns out he hadn't fixed it yet and still needed the help. He was finally able to get it sorted out with a donor eeprom file I sent him for the module. Its a good...
  2. narkeleptk

    Some help please to identify a transistor

    I like mouser personally, many others like digikey. There are other places but I guess these are 2 of the most common.
  3. narkeleptk

    Some help please to identify a transistor

    Snip from datasheet, in case you need to find a substitute,
  4. narkeleptk

    Repair of Oven Control Board - Maytag Range

    Yes you should just be able to buy the same part number. Looking at the datasheet you'd need a dip16 socket.
  5. narkeleptk

    ribbon cable connection repair

    I hate those locking tabs. They love to get brittle and break on at least one side. I usually do like Dave9 suggests with a shim but I reckon the tape is fine. The only thing I would worry about with the tape is if you tried to remove it later on, those types of ribbon cables damage very easily...
  6. narkeleptk

    Repair to Control Board PCB of Whirlpool Oven

    You may find better results searching a LCR meter. Taking measurements in circuit is not usually recommended but sometimes you can get away with it.
  7. narkeleptk

    Treadmill belt won't spin.

    I'd check your relays too. Sometimes they can be damaged from bumping around or maybe the arm had was already weakened from use and then moving it around even a little was enough to finish it off. Never worked on a treadmill but I see it a lot in automotive boxes.
  8. narkeleptk

    Help identifying a diode

    Maybe just a basic ol' 1n4148
  9. narkeleptk

    microsoft surface pro 4 repair

    I checked X first (both with no good results) The smaller image I looked at seemed like it had some faint curves so I was leaning to 8 but this larger blown up one you are providing looks more like an X to me as well now.
  10. narkeleptk

    microsoft surface pro 4 repair

    *shrug* I think its the same board with different lighting and angle. Only TS could really tell us I guess.
  11. narkeleptk

    microsoft surface pro 4 repair

    First picture looks perfectly fine. Second picture looks off but if its same board as the first picture then seems to just be lighting imo.
  12. narkeleptk

    microsoft surface pro 4 repair

    Looks ok to me... Looks cracked. Doesn't necessarily mean its bad, could just be the package but its definitely suspect. I looked a little but did not run across any sot23-6's with code of AJ8. If you find out what it is make sure to let us know !
  13. narkeleptk

    help with Matco Maxme please

    Sure, charging ports are pretty common and basic type of repairs.
  14. narkeleptk

    Module Circuit broken?

    Personally I would secure a new header (the pins) then I would jumper the vcc and ground pins to the large capacitor. The tx/rx I would scratch away the red solder mask on their traces and attach a small wire there to jumper to the header. You could also follow the traces and connect the...
  15. narkeleptk

    I need a relay HJR-3FF-S-Z 24v coil

    If needed later on,its very easy to take a razor and cut around the bottom (just a hair up from bottom edge) to remove the casing.
  16. narkeleptk

    What music do you like?

  17. narkeleptk

    Hi from Das auto center, auto programmer and auto electronics

    Howdy, welcome. You wouldn't happen to have a kess recovery file for a cm2100a PN 4945387, would ya?
  18. narkeleptk

    What music do you like?

    I listen to way too much Coheed & Cambria. If not that then classical piano and violin.
  19. narkeleptk

    Easy Wiring Question

    The doorbell is usually set up around 16VAC. Check your coat closet for a transformer.
  20. narkeleptk

    Can someone simulate this diagram for me please

    I was thinking of using this same schematic for some o2s simulation but never get around to testing it out. If you do try the real thing, let me know how it works out for you.
Top