Search results

  1. GreekPIC

    3-Axis Stepper Controller

    Ebay, DigiKey, Mouser, RS...
  2. GreekPIC

    3-Axis Stepper Controller

    There's a 7805 5V controller onboard. It can take 8-35V as an input (actually whatever voltage the steppers need) and output 5V for the UCN chips Depending on the software you use, you can use NC or that as the switch being pressed and it will stop. You can spare some parallel port pins by...
  3. GreekPIC

    3-Axis Stepper Controller

    I've posted pics on the first pages of this thread. Is your board working ok? Did you work the software settings out? Nikolas
  4. GreekPIC

    3-Axis Stepper Controller

    Like I said, in my opinion EMC2. TurboCNC is easy to setup and runs on old PCs but is rather limited in capabilities. I didn't get into much detail with Mach, but EMC2 seems very impressive. It even has ladder programming (language used in PLCs). Small inkjet printer motors. This is a small...
  5. GreekPIC

    3-Axis Stepper Controller

    TurboCNC. I've tried also Mach2 and CNCplayer. I now downloaded EMC2 and seems like the way to go.
  6. GreekPIC

    3-Axis Stepper Controller

    I'm not familiar with KCam, but you might want to select "Pin setup", that's how it's done to all other programs I've seen. Nikolas
  7. GreekPIC

    3-Axis Stepper Controller

    You got it!
  8. GreekPIC

    3-Axis Stepper Controller

    Nowhere. It's created on the board. Look at the PCB. It's my revised version but the basics are the same: The 12v is connected to the two large pads on the right. The three pads next to them to the left are for the 7805. The lowest (square) is 12v input, the middle is GND and the topmost is...
  9. GreekPIC

    3-Axis Stepper Controller

    It doesn't. It has an on-board 5v power supply circuit with the 7805 regulator. It takes a 8-24v input. You connect 12v to the board. It goes straight to the motors. It also goes through the 7805 to provide 5v for the chips. Nikolas
  10. GreekPIC

    3-Axis Stepper Controller

    MP, his main problem is that he has a bipolar motor while the board only supports unipolar ones (5,6,8 wire motrors). There is a circuit that can be added to the board to drive bipolar motors (I have it around somewhere) but it needs 12 power transistors per motor. It's much better to just look...
  11. GreekPIC

    Siemens screen pinout?

    Thanks for the effort That's it, only mine says DJ390006. It must be serial, having only 10 pins. Any way to reverse engineer it?
  12. GreekPIC

    Siemens screen pinout?

    I'm looking for a datasheet or just the pinout of a C60 screen (model LM15SGFNZ07). It might be made by Sharp but I can't confirm that. Thanks
  13. GreekPIC

    3-Axis Stepper Controller

    On the project page you'll find the schematic, pcb layout and parts overlay in *.ps format. Here is my modification, I changed it a bit to suit my needs. Nikolas
  14. GreekPIC

    What are Heat Sinks??

    Audioguru, heatsinks are actually extrusions, not casts. I've seen a cast heatsink from an old Russian (or should I say Soviet) appliance and it was UGLY! Nikolas
  15. GreekPIC

    How to Read, Write, Print and Email in GREEK (Many Uses!!!)

    Just kidding. On the serious side, I think that someone should have the Greek fonts installed to be able to read what you wrote. Otherwise they would come up looking like skandinavian. The unicode fonts where supposed to solve this problem but very few font creators bother to inlude all the...
  16. GreekPIC

    Spot Welder for batteries

    I'm building one too for making gas turbine parts. Check this page out. You can live without the timing circuit, just rewind the transformer, add a footswitch and a fuse. This site should be interesting to you, also Nikolas
  17. GreekPIC

    How to Read, Write, Print and Email in GREEK (Many Uses!!!)

    Naaah, it just seems Greek to me...  ;D Nikolas
  18. GreekPIC

    WTB TFT controllers

    I'm looking for 17 TFT VGA 640x480 contollers. All I can find online is contollers that can do 640x480 but go up to 1024x768 so they are expensive. I've bought two Digital View ones from ebay for ~45$ over a span of a year but don't want to wait 17 more years for the rest  :P . Doesn anybody...
  19. GreekPIC

    HP VL-609 Motherboard manual or any ideas?

    Ok, small update. I found the PWR SW connection. Shorting pins 1 & 2 powers the system up and holding them for ~10sec turns it off. However it doesn't boot up. So I still need help for the manual (or ideas on what might be wrong). There is a DIP switch on the M/B I can't figure out and I'm...
  20. GreekPIC

    HP VL-609 Motherboard manual or any ideas?

    I saved a motherboard from the trip to the dumpster. It's from a HP machine and I can't find no info for it. What puzzles me is the front panel connector. It doesn't have the usual PWR LED, PWR SW, HD LED etc, pin header. There's only a six pin header labeled "FRCNT CABLE". So, does anybody...
Top