Search results

  1. Maxouishere

    Boosting the Amper and altering the frequency

    @Harald Kapp I think this schematic looks cleaner than above one. What do you think is wrong with it that zener diode burnt?
  2. Maxouishere

    Boosting the Amper and altering the frequency

    1 and 2 are soldered at point 3. (I couldn't draw this. Therefore I indicated it this way.)
  3. Maxouishere

    Boosting the Amper and altering the frequency

    @Harald Kapp Hi. I just tried again with the new voltage regulator. Arduino booted, I read the voltage 0 on multimeter. I remove the cables from battery then tried again. Arduino did not boot this time. There were no smoke or anything. It just stopped working. I think zener diode is burnt...
  4. Maxouishere

    Boosting the Amper and altering the frequency

    Haha. Too late. I already send it to electronics heaven.:)
  5. Maxouishere

    Boosting the Amper and altering the frequency

    Thank you so much! @Harald Kapp Hello. My order has arrived yesterday. I connected everything today. 10-15 sec after the boot, voltage regulator exploded and gray smoke came out. I should have double checked. I falsely connected Ground pin to +in slot of the voltage regulator and Vin to -in...
  6. Maxouishere

    Boosting the Amper and altering the frequency

    I have one more question about this battery that we talked about today: https://www.hepsiburada.com/ttec-12-volt-4-5-amper-bakimsiz-kuru-aku-p-OTKLT927336S It is SLA battery. I read somewhere that I should put fuse in a circuit in case of SLA battery usage. For how long It would last with full...
  7. Maxouishere

    Boosting the Amper and altering the frequency

    Thank you so much for your help so far. I ordered the battery today. I will start experimenting once It arrives. (probably in 2days). Also I have a multimeter too. I bought one when I decided to make my project come alive. Yes, unfortunately I am. But I'm reading papers related to electronics...
  8. Maxouishere

    Boosting the Amper and altering the frequency

    Thanks. I think this one is perfect for my project (1N4732A ~ 4.7V - 1W): https://www.robotsepeti.com/47v-zener-diyot Datasheet: https://html.alldatasheet.com/html-pdf/562541/VISHAY/1N4732A/216/1/1N4732A.html Do you think the battery that you have approved will be sufficient enough to feed 25x...
  9. Maxouishere

    Boosting the Amper and altering the frequency

    Thanks. I was planning to use some sensors to determine swarming, temperature, humidity, etc. Then I better use a zener diode as you said. Does it have to be 4.7V? I found a 5.6V zener diode that looks like a regular diode: https://www.robotistan.com/56-v-zener-diyot-paketi-10-adet And this one...
  10. Maxouishere

    Boosting the Amper and altering the frequency

    Link: https://forum.arduino.cc/t/powering-uno-via-vin-pin-12v-dc-wall-adapter/686071 post #2
  11. Maxouishere

    Boosting the Amper and altering the frequency

    Hello! I am not sure how It works but in the pdfs I read, they refer it as "filling frequency". I will let you know If I find more information related to this. Even If I reduce the output amperes from 0.8A to 0.3A -24V, still wouldn't be enough? I found this battery below. It says 12V - 4.5Ah...
  12. Maxouishere

    Boosting the Amper and altering the frequency

    Hello. Yes, It is for stimulate the bees into ejecting venom. Well, It doesn't have to be exactly 1000Hz. There are different values on Russian pdfs related to bee venom production. Range is 0.5KHz-1.2KHz. I am planning to try different values in this range. The wire is 25/5 Nr-Al (18.80 Ω/m)...
  13. Maxouishere

    Boosting the Amper and altering the frequency

    Thanks! I really appreciate your help. I didn't know that I could draw power from dc barrel jack (I am assuming you are indicating this as Vin) of Arduino. Or I totally misunderstood: Do you mean that I should use Arduino's dc barrel jack to power the Arduino and I should also connect the same...
  14. Maxouishere

    Boosting the Amper and altering the frequency

    Hi. I have some questions If It is OK: 1. Can you suggest a transistor to use in my project? https://www.robotistan.com/transistor-1 2. Do I need a diode for using a transistor or a MOSFET? I watched lots of videos related to them. Some uses diodes, some not. The ones who are using diodes say...
  15. Maxouishere

    Boosting the Amper and altering the frequency

    Glass will be surrounded by "resistance wire" (I'm not sure If this is correct translation to English) like in this video:
  16. Maxouishere

    Boosting the Amper and altering the frequency

    Thanks. I am so new to electronics. I hope I succeed. I will learn about what you have mentioned above in the time I wait for the arrival of my transistors. Thanks. I bought it from this website: https://www.robotistan.com/ayarlanabilir-step-up-boost-voltaj-regulator-karti-xl6009-4-a They...
  17. Maxouishere

    Boosting the Amper and altering the frequency

    Hello. I am trying to build a bee venom collector for my beehive (5x hive) with almost no electrical knowledge. I try to learn while building. After adding necessary components (to increase amps) to the image I posted in this post, I will connect it to my hive. This won't kill the bees, It just...
  18. Maxouishere

    Boosting the Amper and altering the frequency

    Hello. I am using Arduino UNO for a hobby project. I send 5V,1000hz signal through its PWM pin to XL6009E1 voltage regulator to boost the output voltage from 5V to 12-35V. It sends a signal for 2sec and waits for 3sec before sending the signal again. The problem is this voltage regulator has...
View older results
Top