Search results

Search Forums New Posts
  1. Delta Prime

    Need builder for small power supply

    You must be running a fever! But an improved & excellent suggestion.
  2. Delta Prime

    PIR hc sr501 sensitivity

    Could you please elaborate I don't speak moderator It's bad for my rheumatism I know I just made... double secret probation
  3. Delta Prime

    PIR hc sr501 sensitivity

    Yes towards maximum sorry buddy thank you for the thorough explanation.o_O
  4. Delta Prime

    How to make tone and vol switches for Jazzmaster rhythm circuit

    Okay then I'll just delete mine.
  5. Delta Prime

    How to make tone and vol switches for Jazzmaster rhythm circuit

    I envy you!! Sweet!!!! A gorgeous 1959 Jazzmaster with gold anodised pickguard rests on a vintage 5E3 Deluxe. Not a bad Rig......... When the switch is in the ‘up’ or ‘on’ position, the neck pickup is singled out, then routed through a separate set of controls consisting of a 1 meg volume and...
  6. Delta Prime

    PIR hc sr501 sensitivity

    Depends on the configuration of your trim pot! And how you hooked it up! I would start in the middle 500K ohms. But since I've used one the exact same one my findings are. Full CW, the range of sensing increases, and the maximum sensing distance range is approximately 0-9 meters. Full CCW, the...
  7. Delta Prime

    How can I find out the original model number by marking code and top mark?

    A good method is not good enough! The best method through imprinting. Is the first thing you see when you're born.
  8. Delta Prime

    Need builder for small power supply

    Specifications!!how much power?how you going to dissipate the heat? Where are the bubbles and light supposed to come out from? small portion? compressed air! two mechanical diaphragm pumps on the hills of the shoes you put on your feet! Connected to a storage tank via One Way valve. No heat...
  9. Delta Prime

    Inject dc into output side of laptop power supply?

    Or three or four photos. I believe you have way too many solar powered bugs in your system!
  10. Delta Prime

    Canon i865 inkjet printer not powering up after refurbished print head installed

    As you can tell from the "service manual" it is engineered so you can swap out logic boards, printer heads.even upgrade the eproms, nothing will lock up on you or shut down.they wants you to be able to purchase "bookoo" quantities of ink that is their motivation $$$.Could you possibly take...
  11. Delta Prime

    240VAC Power Output on Circuit Board

  12. Delta Prime

    Canon i865 inkjet printer not powering up after refurbished print head installed

  13. Delta Prime

    Canon i865 inkjet printer not powering up after refurbished print head installed

    It seems you like swapping boards the only thing you have not swapped is your logic board. Put this board in your other printer same model. See if any worning lights come on, something blinking. The schematic for that logic board will probably be as thick as a unabridged dictionary.
  14. Delta Prime

    240VAC Power Output on Circuit Board

    Well I'm glad to hear you are your own worst critic is the only thing I could think of that could be the fault. Sorry buddy that's all I could think of. Except check the wiring again there could be a jumper that you have forgotten to replace comparing your board to the stock photo. Or lug nut...
  15. Delta Prime

    240VAC Power Output on Circuit Board

    Well I'm going to have to take your word about the heating element because everything points towards the heating element itself. And that board is rather robust nice thick traces solder pads. If it was me I would look into the return policy if you were to purchase a board and plug it in see if...
  16. Delta Prime

    240VAC Power Output on Circuit Board

    Do you have the old relays? Your solder connections look tip top. Reference the red circle with red arrows Looks like excessive heat what's on the other side?
  17. Delta Prime

    240VAC Power Output on Circuit Board

    This may sound silly but did you check the fuse? I see two of them. Also you my have damaged the traces on the PCB itself perhaps flexing it.
  18. Delta Prime

    240VAC Power Output on Circuit Board

    120VAC with reference to neutral. On both legs. If you measure a cross Leg to leg or hot to hot On the input then yes 240 vac. Now you're measuring on the heating elements expecting to see 240 vac leg to leg and you're measuring 0 volts then your circuit is open. Your concerns are valid you...
  19. Delta Prime

    240VAC Power Output on Circuit Board

    I thought you would never ask! Where in the world are you located? You see saying you have "240VAC coming in" and trying to describe your dilemma means nothing to me. Could you possibly take some photos where you're taking your measurements. They're just too many variables. We must narrow them...
  20. Delta Prime

    Total Electronics Newbie with an idea, LOL

    Welcome to maker pro. You got a schematic? show me? I'm the not so smart one! FDM has the lowest resolution and accuracy when compared to SLA or SLS and is not the best option for printing complex designs or parts with intricate features. But heck I can use a new freshly printed lazy boy...
Top