Search results

Search Forums New Posts
  1. Delta Prime

    Possibly Zener diode identification

    Evaluation: Majority of photographs were not that bad after all. My Resistance to post further in this thread has been overcome by my Capacity to reason clearly, therefore my final thoughts have been Ohmitted.
  2. Delta Prime

    Possibly Zener diode identification

    Behavior and actions reflect my own character my gratitude for your helpful criticism. I must reassess my behavior . Thank you sir.
  3. Delta Prime

    Possibly Zener diode identification

    I could definitely be mistaken considering the horrible photographs taken of the unit. My apologies. I wasn't trying to beat you up. I'm sorry you took it that way.
  4. Delta Prime

    USB 3.1 gen 1 port wiring for charging

    Before you purchase the 7805, if you would like, I could provide you options that will fulfill your requirement, a couple of suggestion perhaps it will still be linear if that's okay.? You're still the boss the answer No,is fine as well. It is what my boss says to me all the time. :(
  5. Delta Prime

    Rumble 150 power problems

    Correction: In post (# 7 ) Misspelling of (printed Circuit board) . "Twice even". My apologies. I normally do it on purpose. :cool:
  6. Delta Prime

    Rumble 150 power problems

    Take a photo of your setup. You probably destroyed your own amp. I like to go perhapsing around with the best of them but it is vital, do you have a combo unit or a single head unit. You're asking for help on a procedural based troubleshooting technique. The above question is asked as a process...
  7. Delta Prime

    Simpson Model 260 7M Calibration

    You're very welcome. In addition to the information stated above. Follow this procedure. 1) Check (Ohmmeter circuit) inside your unit for defective resistors, there is no adjustment potentiometer inside specifically for RX1 scale. 2) short out the banana jacks with a jumper, On RX1 scale, your...
  8. Delta Prime

    Possibly Zener diode identification

    In addition to the above stated excellent information The schematic symbol for the zener diode is While the silk screen designation on the printed circuit board proximal to the mystery component is. It's very good chance it's a house number cuz I can't find it.
  9. Delta Prime

    Cadence Virtuoso. Warning Parameter 'lxUseCell' already exists.

    Hello there welcome to maker pro. I cannot see how without providing your code. You must provide all pertinent information when asking for help.thank you. . You're very lucky my crystal ball is working. I hope this helps. Example! *WARNING* Parameter 'lxUseCell' already exists. End netlist...
  10. Delta Prime

    Hello from Jordan

    Forgive me ,I am only an electronic technician. I should have stated that from the beginning. My employer is a practicing theoretical physicist.I Was just the right place at the right time.relatively speaking... pun intended. I am more proficient at gathering than hunting.
  11. Delta Prime

    Rumble 150 power problems

    The proper way to test the output power.
  12. Delta Prime

    Rumble 150 power problems

    See you tomorrow. Do not make any measurements put the multimeter away for now. Do not apply power to the unit. Unplug it from the wall. Unscrew the case of the unit to gain access to the printer circuit board. Do not put your hands on any part of the printer circuit board. Do not touch...
  13. Delta Prime

    Rumble 150 power problems

    Do you have a combo unit one horn and a speaker?
  14. Delta Prime

    Rumble 150 power problems

    I'll let that one go. At the beginning do you know how to read schematics? You disassembled it. Do you have access printed circuit board? Can you confirm this schematic is your unit that you are inquiring about. If you cannot confirm you must take photos thank you and I'll take it from there!
  15. Delta Prime

    USB 3.1 gen 1 port wiring for charging

    I know what that is... I guess I proved myself wrong. I do know everything.
  16. Delta Prime

    Designing a soldering iron for limited dexterity

    the simplest forms are the best. Inexpensive, Something clear, thin soldering irons, maybe even a glob of silly putty form fitting. perhaps weighted if you suffer from tremors shaky hands. Can be very adaptable. Again depending on your ailment. Below I can think of something more secure...
  17. Delta Prime

    Simpson Model 260 7M Calibration

    .
  18. Delta Prime

    Simpson Model 260 7M Calibration

    .
  19. Delta Prime

    Simpson Model 260 7M Calibration

    Quick search didn't take long. But I'm happy you came here first. And it's free to download. If you have any other questions please do not hesitate to ask. https://www.simpson260.com/downloads/downloads.htm
  20. Delta Prime

    Hello from Jordan

    You have my condolences. I'm allowed to say that I am cross-disciplined my primary responsibility my occupation is research modifying and building electronic equipment for experimentation in a laboratory setting. I employ the majority of scientific disciplines.I'm a master of none. I reek of...
Top