kosoniscs Posted March 3, 2006 Report Share Posted March 3, 2006 I need to control a DC motor using PWM signal from a microcontroler. I found several componets easy to use but they are low current. The motor that I'm going to control works with 12V and 35 amps in pick. Once I will reverse it frequentily I think that I should make a project considering 35 amps nominal current.I don't have experience in this kind of project, so that I need some help with circuits and components.Thanks.. Quote Link to comment Share on other sites More sharing options...
gogo2520 Posted March 4, 2006 Report Share Posted March 4, 2006 Hello Kosoniscs 35amps wow, your talking 10 or 8 gage wire. A pcb couldln't handle that kind of current so you would have to build it in modules using isolators. I'm thinking three modules. One for the low curent comos controllers, second for chopping the curent, and third for relays to handle the current. The third one would be the hardiest because you would have to find fast switching relays that you could hard wire togeather. I'm guessing that if you hang in on this site the real smart electronic guys will come up with something. Good luck gogo Quote Link to comment Share on other sites More sharing options...
William Myblueroom Posted March 4, 2006 Report Share Posted March 4, 2006 A big h-bridge, look for IRF540 HEXFET drivers You'll need at least 2 of them in parallel for more current. IRF9540 P Channel and wire them into a driver like a TC4424 Quote Link to comment Share on other sites More sharing options...
Berni Posted March 5, 2006 Report Share Posted March 5, 2006 the IRF3205 is rated at 80A and in a TO-220 So this should run even on y small heatsink.I also reconend MOSFET gate drivers especialy if you are going to use PWM. Quote Link to comment Share on other sites More sharing options...
kosoniscs Posted March 8, 2006 Author Report Share Posted March 8, 2006 Thanks for all.I also believe that using MOSFET is the best choice. I've never made a circuit using them, so that I don't know what dificults I may found by build the bridge. Quote Link to comment Share on other sites More sharing options...
ante Posted March 8, 2006 Report Share Posted March 8, 2006 Why an H-Bridge? Quote Link to comment Share on other sites More sharing options...
kosoniscs Posted March 9, 2006 Author Report Share Posted March 9, 2006 Because I have to control the motor in both directions and this is the only circuit that I know to do this. Is there an easier?Thanks Quote Link to comment Share on other sites More sharing options...
ante Posted March 9, 2006 Report Share Posted March 9, 2006 Well, in that case maybe not! ;) Quote Link to comment Share on other sites More sharing options...
Cryonic Posted March 17, 2006 Report Share Posted March 17, 2006 It may also be possible to use two starter motor relays to change the polarity, and only one MOSFET as PWM motor driver. Just throwing in my dumpster diving rock bottom penny broke approach.And if you insist on using an H-Bridge, then you may find these links usefull:Power control, with H-Bridge concepts and schematics in design:http://users.pandora.be/educypedia/electronics/powercontrol.htmH-Bridge Controller IC for Automotive DC Motors (Datasheet is also available):http://www.irf.com/product-info/auto/autohbridge.htmlBrief H-Bridge Theory of Operation (Good links):http://www.dprg.org/tutorials/1998-04a/index.htmlVoltage Spikes in FET based H-bridges - By Chuck McManis - 2002 (Please read this, very informative !):http://www.mcmanis.com/chuck/robotics/projects/esc2/hbridge_spiking.htmlMotor and General Control Schematics (Links to some good sites):http://hobbyprojects.com/quick_circuits_reference/motor_and_general_control_schematics.htmlYou can also Google: "MOSFET H-Bridge Schematic"Remark:Many designs I have seen on the Internet lack sufficient protection of MOSFET's against induction spikes caused by the Motor. They are easily destroyed by insufficient precautions against this, especially via feedback into the Gate of the MOSFET.Success with your project !Cryonic. Quote Link to comment Share on other sites More sharing options...
kosoniscs Posted March 23, 2006 Author Report Share Posted March 23, 2006 Thanks a lot! Very good links... Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.