Search results

Search Forums New Posts
  1. Maglatron

    help with IR2110 chips

    I still think that there needs to be a gap at least the size of the cores = 15mm, between magnets
  2. Maglatron

    help with IR2110 chips

    the wheel I'm using is identical to the one in the pic just without any magnets stuck to it yet! was just to show you the spacing of the 8 magnet wheel! for your viewing pleasure I will be sticking 16 magnets either side doubled up that's 64 magnets in total!
  3. Maglatron

    help with IR2110 chips

    ok thanks I'll fit the 16 how did you calcultate it? also did you see the picture witht the wheel with 8 on I don't think that 18 would fit to be honest
  4. Maglatron

    help with IR2110 chips

    getting glue tomorrow hopefully get to fit the magnets to the spare wheel! have to decide if I'm goin with 14-a-side or 16-a-side! any ideas??
  5. Maglatron

    help with IR2110 chips

    I have an older picture might help visualize the 8-a-side wheel
  6. Maglatron

    help with IR2110 chips

    I cannot see the digits on this picture too low resolution!! thanks
  7. Maglatron

    help with IR2110 chips

    I took the plunge and got enough for 16-a-side!
  8. Maglatron

    help with IR2110 chips

    using this sense, would 16 magnets be 100%
  9. Maglatron

    help with IR2110 chips

    do you think 12 or even 14 magnets or even 16 magnets a side would be better, in your opinion I have enough for 12-a-side right now as we speak
  10. Maglatron

    help with IR2110 chips

    the gap should be at least as big as the core that the magnets pass
  11. Maglatron

    help with IR2110 chips

    I'll take photos when I get a chance I purposly put the magnets closer to the middle than the edge and thats because they have less magnetic cogging effect and so the wheel spins faster with more ease and less labour on the motor driving the wheel. do you think that you can put alternating...
  12. Maglatron

    help with IR2110 chips

    did you get to use the information in the end?
  13. Maglatron

    help with IR2110 chips

    and the wheel is actuall 28cm in diameter and the magnets center is 7cm from the center of the disk
  14. Maglatron

    help with IR2110 chips

    so I took off the old wheel (looking very naked now) removed the back two coils. no super glue to glue on the magnets!!! going to have to get some asap the gaps between the magnets on the 8-a-side wheel are much bigger than I remember just did some solder work on the spectrum analyser board...
  15. Maglatron

    help with IR2110 chips

    my simbox shows different that your Mr Harald Kapp
  16. Maglatron

    help with IR2110 chips

    as you can see there is a phase shift of 90 degrees on each coil
  17. Maglatron

    help with IR2110 chips

    this is better the phase shift is 0 90 180 and 270! just number 5 that has the same as 4
  18. Maglatron

    help with IR2110 chips

    I tried 5 coils in the sim and get this,
  19. Maglatron

    help with IR2110 chips

    the rubber disk are 30cm in diameter the magnets are 2.5cm in diameter 3mm thick doubled up to make 6mm of magnet, the magnets are situated 7.5 cm from the axis there are 8 magnets either side or 16 if you double them up but effectively 8 magnets either side! going to put 10 on either side of...
  20. Maglatron

    Comedy Thread

    man goes to a zoo with the family, there was only one animal, the dad goes this is a shit zoo!
Top