Search results

Search Forums New Posts
  1. Maglatron

    help with IR2110 chips

    so the reds are the front and blue the back, with 10 magnets in phase back and front, coil 5 would be in phase with 2 and 3, with magnets passing at the same time, and 1 and 4 would be in phase and have magnets passing those at the same time!! might just be able to fit a 6th coil on either the...
  2. Maglatron

    help with IR2110 chips

    so just to clarify do you think the magnets should be in phase? thanks The post #448 arrangement doesn't provide voltage doubling, but would provide voltage addition if diodes D3 and D4 were removed. However, because coil pairs 1 and 2 are not in phase their voltages partly cancel during parts...
  3. Maglatron

    help with IR2110 chips

    ok I'll get back to you when I've wound and fitted the identical 7 ohm coil, thanks, see the outcome and go from there!
  4. Maglatron

    help with IR2110 chips

    I'll check back when I have wound and fitted the other 7ohm coil!
  5. Maglatron

    help with IR2110 chips

    found some the same size and weight as the two that I have!
  6. Maglatron

    help with IR2110 chips

    actually comes between 7th and 14th of this month
  7. Maglatron

    help with IR2110 chips

    ok so I know you said it was a bad idea to buy anything else but I have to see this through so I have bought 6 coils guage 0.724 500gram, so should be a bit less than 7ohm I get my new magnets tomorrow and will put 10 either side and without the phase shift of 120 degrees, on to my spare...
  8. Maglatron

    help with IR2110 chips

    you can't rectify 1 coil to dc?
  9. Maglatron

    help with IR2110 chips

    yes ok so how would you wire up a bridge rectifier with the one coil because when I measured it my way it gave 28volts rectified, I want to see how you would do it can I get a spice image please, thanks
  10. Maglatron

    help with IR2110 chips

    ok I'll start with the two that I do have and try and work out how much I can get from them
  11. Maglatron

    help with IR2110 chips

    my transformer is a 230primary and 15 0 15 on the secondary coils I can parallel the output coils so that the ratio stays at 15.3 to 1 and use the secondaries as the primary the secondary will be splitting the resistance between two as well, so the resistance of the secondary will be halved but...
  12. Maglatron

    help with IR2110 chips

    they dont have the same ones in stock that I bought last time!
  13. Maglatron

    help with IR2110 chips

    so what is better 123meters of 0.724 or 195meter of 0.574
  14. Maglatron

    help with IR2110 chips

    so I'm buying more of the copper wire and they don't have any 0.7mm they do have 0.724 and 0.574 what would you get?
  15. Maglatron

    help with IR2110 chips

    so if I get 6 on then I'll be safe and also do you think I should mitigate the shift in phase? I'll be using 10 magnets
  16. Maglatron

    help with IR2110 chips

    5 in total? might be do able
  17. Maglatron

    help with IR2110 chips

    is this what you meant
  18. Maglatron

    help with IR2110 chips

    from what I understood the rotary generator that you modelled was to half the resistance and double the current or am I missing something, I only half understand whats going on in that spice model winding another coil today and am going to fit it, then we have two coils to work with that are...
  19. Maglatron

    help with IR2110 chips

    no I didn't understand it properly but this is the measurement of one coil, can you post again how you suggested please I'm getting confused, or tell me which post number it was, thanks
  20. Maglatron

    help with IR2110 chips

    this is the meter I used...
Top