Search results

Search Forums New Posts
  1. Martaine2005

    Replacement LED for Guitar Effects Pedal (Ibanez Tone-Lok CF7)

    If you have diode function on your meter, you can test the LED. Martin
  2. Martaine2005

    Replacement LED for Guitar Effects Pedal (Ibanez Tone-Lok CF7)

    Yes, you can pretty much replace it with any LED. But, it would be a good idea to locate it’s current limiting resistor close to it. I would just solder a new red one in. Not the clear type though. Have you got a multimeter? Martin
  3. Martaine2005

    Just joined from Alabama

    Welcome to EP Martin
  4. Martaine2005

    Tape deck power issue

    Well, you can sell it with ‘new’ belts fitted. :) Shame really. Martin
  5. Martaine2005

    Tape deck power issue

    Highly unlikely the board got damaged. Possibly a wire or connection broke while taking it apart. Unfortunately, you will need a multimeter or some kind of continuity tester to check. Martin
  6. Martaine2005

    blew up 2 pin to uk 3 pin android mi box

    Two pin is usually European or US. Is your box 220V or 110V? Martin
  7. Martaine2005

    Noise suppression problems attempting to to mate power amplifier with PC power supply.

    Ok, but you still need an audio input from a device. Do you have a pre-amp or sound card connected?. How is this connected to the computer?. Martin
  8. Martaine2005

    Noise suppression problems attempting to to mate power amplifier with PC power supply.

    Yes, I understand that. Are you using each input with a device? ie, ipod on input 1, iphone on input 2, ps4 on input 3 etc. Martin
  9. Martaine2005

    Noise suppression problems attempting to to mate power amplifier with PC power supply.

    That would depend on what audio signals you have as inputs. Are you using all 4 inputs for different audio devices? I use an audio mixer with only one main output. But I use one for each laptop output to the mixer. Martin
  10. Martaine2005

    Tape deck power issue

    I would suggest taking it a part again to re-trace your steps. Check connectors orientation and that they are seated correctly. This is obviously no coincidence. Martin
  11. Martaine2005

    Noise suppression problems attempting to to mate power amplifier with PC power supply.

    Hi Kevin, you might want to try a ground loop isolator rather than a power line noise suppressor. Use it at the audio input. I have several for a mobile disco and they work great. Martin
  12. Martaine2005

    Hot air gun plug standard

    Sorry.....Missed that.
  13. Martaine2005

    Hot air gun plug standard

    This one here on Amazon has the same amount of pins and a wide choice of units it fits. Still confused though!. Does your station have a connector? or are you adding a connector to it and a new heat gun? Martin
  14. Martaine2005

    Hot air gun plug standard

    I got a little lost and confused...... A soldering iron has the connector. The heat gun has a tube. This hasn't got a connector. Martin
  15. Martaine2005

    Hot air gun plug standard

    I just deleted my post. Martin
  16. Martaine2005

    Hot air gun plug standard

    If you give us more information on your unit, we may be able to help you further. As you have seen, some have more connections than others. But we're guessing as you have not supplied any info at all. Martin
  17. Martaine2005

    Power transistor identification

    Those vacuum solder suckers are great. I had to practice for a while as I pulled a few solder pads at first. Martin
  18. Martaine2005

    Isolating constant from flashing signal

    I do believe we are thinking the same!. Martin
  19. Martaine2005

    Hot air gun plug standard

    May be one of these will help. Martin
  20. Martaine2005

    Hot air gun plug standard

    Hot air gun? What type? mains or 24V? Paint stripper type or hot air solder re-work type Martin
Top