Search results

Search Forums New Posts
  1. Arouse1973

    diesel engine controller water damage

    Hello. Can you take it apart and take some close up pictures. With it taken apart put it in the oven for an hour at say 50 degrees C , if your oven goes that low. see if that helps. Adam
  2. Arouse1973

    Relationship of frequency and capacitance.

    As always Ratch, very good. Adam
  3. Arouse1973

    Introduction

    Hello Albert, welcome. If it means drinking 10 pints of Cider and eating 10 packets of crisps then I will co-operate I promise. :) Adam
  4. Arouse1973

    PCB gerber changes

    Oh Ok that's quite handy. Adam
  5. Arouse1973

    PCB gerber changes

    What Gerber software are you using? Adam
  6. Arouse1973

    PCB gerber changes

    Hello Philip How large is the PCB? Could you use a demo licence? Does the customer have the Software you could borrow? Or was it designed by another contractor? A lot of good PCB design packages have translators so you covert from one PCB package to another, does EasyPC have this? I guess you...
  7. Arouse1973

    PCB minimum thickness (rigid)

    You tell them the thickness you want, they will tell you if they can make it. I get manufactured thousands of 8 layer, 6 Layer and 4 Layer PCBs each year at 1.6 mm +/- 10% FR4 with no problems. Adam
  8. Arouse1973

    Help mitre saw blows house fuse

    Put it back together and tell them your going to contact trading standards or HSE. it shouldnt do this if rated for the UK and your using it from a standard UK wired socket. Adam
  9. Arouse1973

    Piezo to Capacitor

    Do you really? Anyway, if you put more energy into a capacitor than you take out of it then it will store energy. It does not matter the size. Adam
  10. Arouse1973

    Piezo to Capacitor

    It the same as the question you asked before. What is it you dont understand about power, current, and voltage. There is something? Adam
  11. Arouse1973

    momentary relay switch push activated

    Hello Replace C2 with a 10K and connect the switch from pin 2 to GND. Thanks Miss Piggy
  12. Arouse1973

    Generator protection

    Sorry I don't have the time to do your searching at the moment. Thanks Adam
  13. Arouse1973

    Generator protection

    No problem. I would try and get an RCBO if you can. You need to make sure it trips before an excessive load damages anything. But the equipment data sheet does say it's protected. Adam
  14. Arouse1973

    Generator protection

    Hello The datasheet tells you the maximum current for both DC and AC. 5 Amp for DC and circuit protector at 11.5A for 230 V AC. 1.8KVa at 230 V is 7.8 Amp, 1.8KVa at 120 V is 15 Amps. You choose. Thanks Adam
  15. Arouse1973

    Can anyone Identify this component?

    I am thinking a 1uF 35V Tant, but to be honest I have never seen them look like that before. One of the other guys might know for definite. Adam
  16. Arouse1973

    Hello, Welcome! (Introduce yourself)

    Hello Diogo and welcome to EP Adam
  17. Arouse1973

    Hovering Drone....W/Kg Calculation.....

    This is getting interesting now, carry on! Adam
  18. Arouse1973

    Piezo to Capacitor

    If you add two energy sources in parallel that dont interact with each other and remove energy from each other then yes.. Adam
  19. Arouse1973

    Piezo to Capacitor

    Sorry you lost me. What do you mean? Adam
  20. Arouse1973

    Controlling power mosfet

    As Bob kindly chipped in with the answer I agree with Bob. Adam
Top