Search results

Search Forums New Posts
  1. Martaine2005

    Dewalt dcb101 drill battery charger

    Isopropyl is a good all round cleaner. But any pcb cleaner should remove water marks. That is why I suggested cleaning the board. Because those marks may or may not be damage. If it's a little damaged track, it can be repaired by bridging another wire to the next component. But one step at a...
  2. Martaine2005

    Dewalt dcb101 drill battery charger

    Hello, That was rather unfortunate. If you are very lucky, it could be just the fuse. In your first picture by the two black wires, there is a small black circular device. That looks like the pcb fuse. You can check that with simple continuity. I would clean the board as well, because water...
  3. Martaine2005

    I'm a Carpenter, not an Electrical Engineer

    I am sure there are members putting your circuit into simulators as we speak!. But there is a lot of info to read first. Martin
  4. Martaine2005

    Choice of PCB drill and stand (Dremel?)

    Minicraft are still sold regularly on Ebay. And they have larger chucks too.. http://www.ebay.co.uk/itm/Minicraft-Lathe-with-drill-included-/191760056000?hash=item2ca5ca3ec0:g:1QAAAOSw1S9WbxML But if you want to drill bigger holes, then you need a bigger drill. I am sure you can find third...
  5. Martaine2005

    I'm a Carpenter, not an Electrical Engineer

    I don't like Chinese tools!!:eek: Bob started it..:D
  6. Martaine2005

    Digital Multimeter Problem "-1" !!!

    I am not sure of your fault finding experience, Most DMMs have very similar protection circuits. (according to Dave Jones) This video might be very helpful.. Jump to 15:50 if you are not interested in the Amps side.
  7. Martaine2005

    Best crimping tools for DIY

    Yes, it does the usual cheap crimps. Blue, yellow and red.. Martin
  8. Martaine2005

    Anyone near Indiana?

    What a lovely photo John.. All jokes aside.. Martin
  9. Martaine2005

    Anyone near Indiana?

    Haha, finally... Free Willie was a good film:p
  10. Martaine2005

    Simple latching switch for a pcb

    This site HERE!!! Noboby said "oi listen" Hear me now? I replied here to show you I hear what you are saying! A forum without audio! EP? Here? Or a figure of speech? Here is best? To listen ? Hear.... Yeah, you are right....As Uncle Chris would say "I goofed big time"!!!:p Thanks for the...
  11. Martaine2005

    I'm a Carpenter, not an Electrical Engineer

    Lol @ Noah from now on!! Did your friends (oops) come two by two:p:p Sorry, but that is just funny... No offence ...... Just a joke!! Martin
  12. Martaine2005

    I'm a Carpenter, not an Electrical Engineer

    Ah A finish carpenter!! That would be our bespoke joiner! Here in the United States of Scotland , Wales, Ireland And HERE ENGLAND, The carpenter (me) chooses the stock...The carpenter (me) cuts the stock.. The carpenter (me) shapes the stock...Etc I used to send lorry loads back to the...
  13. Martaine2005

    Anyone near Indiana?

    I guess it now makes sense?
  14. Martaine2005

    Anyone near Indiana?

    Geez John, The Clinton River...:eek:
  15. Martaine2005

    Need a pinouts of HG1700AG27 IMU ?

    All I can find is aviation equipment. Martin
  16. Martaine2005

    Simple latching switch for a pcb

    Here here.... I couldn't have put it better!! Martin
  17. Martaine2005

    Anyone near Indiana?

    @Tha fios agaibh Did the Monica make sense?
  18. Martaine2005

    3.2v LEDs 12v battery

    Thank you.. Happy soldering.:)
  19. Martaine2005

    3.2v LEDs 12v battery

    150 ohm is perfect..
  20. Martaine2005

    Help! Repairing water damaged PCB from Massage chair.

    Sorry for the delay in replying. Your pictures show many legs of componets that have rust. I think it would be advantageous to remove them all, clean the leads and pcb, then check the components out of circuit before re-assembly. You could of course just flux the whole board and re-solder each...
View older results
Top