Frequency Response of Amplifiers
 Boris Poupet
 bpoupet@hotmail.fr
 12 min

8943Views
 1 Comments
Introduction
As such for any electronic circuit, the behavior of amplifiers is affected by the frequency of the signal on their input terminal. This characteristic is known as the frequency response.
Frequency response is one of the most important property of amplifiers. In the frequency range that amplifiers have been designed for, they must deliver a constant and acceptable level of gain. The frequency response depends directly on the components and the architecture chosen for the design of the amplifier.
In this tutorial, we will focus on this important feature of amplifiers. First of all, the notion of frequency response is detailed along with some basic related concepts and we will present how to quantify it. In the second section, we will understand which component affects the frequency response and how. In the rest of the article a method to establish the low and high frequency responses is presented. These results will finally be synthesized in the conclusion to plot the global frequency response of a Common Emitter Amplifier.
Definitions
Before defining in details the frequency response, we need to present the unit of decibel (dB) and the logarithmic scale related to it. When studying the frequency response, it is indeed more suitable to convert either the power or voltage gain into dB and to represent the frequency scale in a logarithmic (log) scale.
If we consider an amplifier with power gain A_{P }and voltage gain A_{V}, the power and voltage gain in dB are defined by :
While the gains in linear scale are always positive (A_{P},A_{V}≥0), their equivalent in dB can either be positive if an amplification is being realized (A_{P},A_{V}>1) or negative if the input signal is attenuated (A_{P},A_{V}<1).
Often, it is not the gain A_{V}(dB) that is investigated but rather a normalized ratio A_{V}/A_{V}_{,mid}(dB)=20log(A_{V}/A_{V,mid}). Where A_{V,mid} is called the midrange gain and represents the maximum gain of the amplifier in its frequency working range, for example 20 Hz – 20 kHz for an audio amplifier.
Therefore, when A_{V}=A_{V,mid}, the normalized gain (written indifferently A_{V}) is A_{V}(dB)=0_{.} This sets a 0 dB reference when the gain is maximum. It is important to note that when the power is divided by two, we observe that A_{P}(dB)=10log(0.5)=3 dB.
The frequency at which the power drops to 50 % of its midrange value is known as the cutoff frequency and noted f_{c}. Each time that the power is halved, a reduction of 3 dB of the normalized gain is observed. Therefore A_{P}=3 dB corresponds to A_{V,mid}/2, A_{P}=6 dB corresponds to A_{V}_{,mid}/4 and so on …
For this same frequency, the voltage (or current) is multiplied by a factor √2=0.7. Halving the voltage signal corresponds to a reduction of 6 dB and follows the same pattern as presented for the power gain.
The most common tool used to represent the frequency response of any system is the Bode plot. It consists of the normalized gain A_{V}(dB) as a function of the frequency in log scale. A simplified Bode graph of an amplifier is shown in the Figure 1 below :
The light blue curve is called the asymptotic representation while the dark blue curve is the real frequency response of the circuit.
In Figure 1, two different cutoff frequencies can be distinguished : f_{lc} for “low cutoff” and f_{hc} for “high cutoff”. The quantity f_{hc}f_{lc }is called the bandwidth and represents the frequency range where the gain is above the 3 dB plateau.
One last observation can be given about the slope of the frequency response out of the bandwidth. First of all, they are not necessary identical for low and high frequencies. Moreover, as we will see later, the slope has a value that depends on the reactance of the components that induce a dependency with the frequency.
Effect of the capacitors
Let’s consider a Common Emitter Amplifier (CEA) which configuration is shown in Figure 2 :
The structure around the BJT transistor consists of a voltage divider network (R_{1} and R_{2}), a load (R_{L}), coupling capacitors (C_{1} and C_{3}) and a bypass capacitor C_{2}.
What is important to keep in mind is that capacitors have a property called reactance that is an equivalent of the resistance. The reactance (X_{C}) of capacitors depends on the frequency and the value of the capacitor, it satisfies the following formula :
Independently of the value of the capacitor, when the frequency is low, X_{C} tends to be high. Near DC signals, capacitors behave therefore as open circuits. On the other hand, when the frequency increases X_{C} tends to zero and capacitors act as short circuits.
At low input frequencies, the coupling capacitors will more likely block the signal, since X_{C}_{1} and X_{C3} are higher, more voltage drop will be observed across C_{1} and C_{3}. This results in a lower voltage gain.
At high input frequencies the bypass capacitor C_{2 }shortens the emitter branch to the ground and the voltage gain of the amplifier is A_{V}=(R_{C}//R_{L})/r_{e} with r_{e} being the small diode emitter resistance. When the frequencies are lower, the resistance between the emitter and the ground is no longer only r_{e} but R_{E}+r_{e} and therefore the voltage gain decreases to A_{V}=(R_{C}//R_{L})/(R_{E}+r_{e}).
There is another type of capacitors that affect the frequency response of the amplifier and is not represented in Figure 2. They are known as internal transistor capacitors and represented in Figure 3 below :
Whereas the coupling and bypass capacitors act as highpass filter (they block low frequencies), these internal capacitors behave differently. Indeed, if the frequency is low, C_{BC }and C_{BE }act as an open circuit and the transistor is not affected at all. However, if the frequency increases, more signal passes through them instead of going in the base branch of the transistor, therefore decreasing the voltage gain.
A very important formula is given in Equation 3 and links the cutoff frequency of a RC filter :
Low frequency response
Having all of this information in mind, let’s calculate and plot the low frequency response of the CEA of Figure 2 with the below given parameters :
 R_{S}=500 Ω ; R_{1}=80 kΩ ; R_{2}=30 kΩ ; R_{C}=5 kΩ ; R_{E}=2 kΩ ; R_{L}=6 kΩ ; r_{e}= 25 Ω
 C_{1}=100 nF ; C_{2}=150 μF ; C_{3}=400 nF ; C_{BC}=5 pF ; C_{BE}=30 pF
 Gain of the transistor β=100 ; V_{supply}=10 V
First of all we consider the input highpass filter R_{in}C_{1}. As explained in previous tutorials, R_{in }is the total input impedance of the amplifier. In our example, it can be determined by ]
R_{in}=R_{S}+(R_{1}//R_{2}//βR_{E})=20.2 kΩ.
The low cutoff frequency of the input will therefore be : f_{cl,in}=1/(2πR_{in}C_{1})=79 Hz.
The same procedure can be done for the output where the output resistance is R_{out}=R_{C}//R_{L}=2.7 kΩ. The low cutoff frequency of the output filter is : f_{cl,out}=1/(2πR_{out}C_{3})=147 Hz.
Finally, for the bypass capacitor, the resistance formula is more complex and given by R_{bypass}=R_{E}//((r_{e}+(R_{S}//βR_{E})/β))=30 Ω. The low cutoff frequency of the bypass structure is thus :
f_{cl,bypass}=1/(2πR_{bypass}C_{2})=35 Hz.
One last thing we need to understand before plotting the Bode graph is about the slope out of the midrange values. The decrease of A_{V,mid} with the frequency is called rolloff and its value for each simple RC filter is 20 dB/decade (dB/dec). This value means for highpass filters (resp. lowpass filters) that each time the frequency is divided by 10 (resp. multiplied by 10), a decrease of 20 dB is observed for the gain of the amplifier.
When multiple filters are blocking the same range of frequencies, the rolloff is enhanced. In our example three filters are simultaneously blocking the frequencies below 35 Hz, the rolloff is therefore 3*(20 dB/dec)=60 dB/dec.
This information can be synthesized in a Bode plot showing the low frequency response of the CEA in asymptotic representation :
High frequency response
As stated previously, it is the internal transistor capacitors that will limit the gain at high frequencies acting as lowpass filters. It can be shown that the equivalent circuit of Figure 2 at high frequency can be drawn such as presented in Figure 5 :
We can note that the coupling capacitors are not represented since they behave as short circuits at high frequencies. Moreover, the emitter branch is shorten to the ground for the same reason applying to the bypass capacitor.
The internal capacitor C_{BC} is converted via Miller’s theorem into the equivalent C_{in }and C_{out} capacitors. Moreover, this theorem states that C_{in}=C_{BC}(A_{V,mid}+1) and C_{out}=C_{BC}(A_{V,mid}+1)/A_{V,mid}.
The total input capacitance of this circuit is C_{IN}=C_{BE}+C_{in }; the total input resistance is R_{IN}=R_{S}//R_{1}//R_{2}//βr_{e}. The numerical application to our example gives A_{V,mid}=(R_{C}//R_{L})/r_{e}=108, C_{IN}=575 pF and R_{IN}=409 Ω. The high cutoff frequency of the input is therefore f_{hc,in}=1/(2πR_{IN}C_{IN})=677 kHz.
From the output point of view, the high cutoff frequency is simply given by the filter (R_{C}//R_{L})C_{out} with C_{out}=5.3 pF : f_{hc,out}=1/(2π(R_{C}//R_{L})C_{out})=1.1 MHz.
The information given here is summarized in a Bode plot representing the high frequency response of the CEA in asymptotic representation :
Conclusion
We have presented some keyconcepts such as the decibel unit and the cutoff frequency in order to understand the idea of frequency response.
We have seen that many different types of capacitors influence both the low and high frequency response of amplifiers. Coupling and bypass capacitors indeed limit the low frequency response whereas the internal transistor capacitors limit the high frequency response.
In the two last sections, we show a step by step method to determine separately the low and high frequency response of a typical CEA configuration.
By merging the two Bode graphs obtained for the low and high frequency responses in Figure 4 and 6, we can now plot the overall frequency response of the CEA configuration :
Comments
Having one put on yourself
6 months ago