Sensor board for micro:bit
https://www.electronics-lab.com/sensor-board-microbit/
The MonkMakes Sensor Board for micro:bit allows you to sense sound level, temperature and light level. Features 3V and GND connections can be made from either side and allow you to power a second board such as the MonkMakes Relay Board or MonkMakes Speaker. LED ‘power on’ indicator Reverse polarity protection All three sensors are analog […]
SprintIR6S, World’s Fastest NDIR CO2 Sensor
https://www.electronics-lab.com/sprintir6s-worlds-fastest-ndir-co2-sensor/
Gas Sensing Solutions (GSS) Ltd is a designer and manufacturer of low power, high speed Non-Dispersive Infrared (NDIR) carbon dioxide gas sensors. Recently, it has claimed a new speed record for its SprintIR6S NDIR CO2 sensor. The new sensor comes with response rates that had never been reached before by any other NDIR CO2 sensors. It can […]
2018 Will Mark A Milestone in GNSS Technology with 30-centimeter Accuracy
https://www.electronics-lab.com/2018-will-mark-milestone-gps-technology-30-centimeter-accuracy/
You’re in a crowded street with many high buildings around you and you find your car position on Google maps is wrong. That’s usual, right? This is caused from (fake/distorted) GPS signals reflected from the high buildings around you which make your GPS receiver do some wrong calculations. So be careful don’t always listen to […]
50V – 10A Bidirectional DC Motor Driver Using A3941
https://www.electronics-lab.com/50v-10a-bidirectional-dc-motor-driver-using-a3941/
This tiny board designed to drive bidirectional DC brushed motor of large current. DC supply is up to 50V DC. A3941 gate driver IC and 4X N Channel Mosfet IRLR024 used as H-Bridge. The project can handle a load up to 10Amps. Screw terminals provided to connect load and load supply, 9 Pin header connector […]
50V – 10A Bidirectional DC Motor Driver Using A3941
https://www.electronics-lab.com/project/50v-10a-bidirectional-dc-motor-driver-using-a3941/
This tiny board is designed to drive a bidirectional DC brushed motor of large current. DC supply is up to 50V DC. A3941 gate driver IC and 4X N Channel Mosfet IRLR024 used as H-Bridge. The project can handle a load of up to 10A. Screw terminals are provided to connect the load and load […]
IoT Projects Is Now Easier With Bolt IoT Platform
https://www.electronics-lab.com/bolt-iot-platform/
Internet of Things (IoT) is one of the most important technologies these days. It became an essential component of many hardware projects core. And in order to make it easier for developers, Bolt IoT platform appeared as a complete solution for IoT projects. Bolt is a combination of hardware and cloud service that allow users […]
Grid-connected solar microinverter reference design
https://www.electronics-lab.com/grid-connected-solar-microinverter-reference-design/
A PDF from Microchip on the theory behind inverter design connected to grip power.: There are two main requirements for solar inverter systems: harvest available energy from the PV panel and inject a sinusoidal current into the grid in phase with the grid voltage. In order to harvest the energy out of the PV panel, […]
uBoost Single AA to 3.3v 100mA Power Supply
https://www.electronics-lab.com/uboost-single-aa-3-3v-100ma-power-supply/
µBoost is a Single AA powered, 3.3v 100mA power source and flashlight and it can run low power devices. µBoost is small, portable, 3.3v 100mA power source for low power devices like Arduino Mini. It has white power LED and can usable as flashlight. Also it has “Battery OK” indicator that asserts when the battery […]
Open Radiation Detector
https://www.electronics-lab.com/open-radiation-detector-2/
Quickly identify radioactive materials with a pocket-sized ion chamber. Built from standard parts for easy manufacture and low cost. by Carlos Garcia Saura: Radioactivity is invisible and can be harmful to life. The goal of this project is to provide a simple device that could prevent cases of radiation poisoning. Professional radiation meters can be […]
Da Vinci Color, The First Full Color 3D Printer
https://www.electronics-lab.com/da-vinci-color-first-full-color-3d-printer/
3D Printing became an important process in prototyping, and sometimes in manufacturing. But till now, the filament types available in the market are limiting printing colors. Although there are many multi color printers, printing a design in full color is still a dream. XYZprinting has announced its da Vinci Color printer, the world’s first full color […]