XMotion All In One Controller for Robotics
https://www.electronics-lab.com/xmotion-one-controller-robotics/
If there is a motion, it must have XMotion. Recreating Arduino & interface circuits user focused. XMotion is Arduino Compatible all in one robot controller. Which designed specially for robotics, IOT and maker projects. It includes powerful Motor drivers, switching mode regulator, interface circuits and more. With protected features, it is all in one board […]
50V – 10A Bidirectional DC Motor Driver Using A3941
https://www.electronics-lab.com/50v-10a-bidirectional-dc-motor-driver-using-a3941/
This tiny board designed to drive bidirectional DC brushed motor of large current. DC supply is up to 50V DC. A3941 gate driver IC and 4X N Channel Mosfet IRLR024 used as H-Bridge. The project can handle a load up to 10Amps. Screw terminals provided to connect load and load supply, 9 Pin header connector […]
10A 400V DC Intelligent Power Module (IPM)
https://www.electronics-lab.com/10a-400v-dc-intelligent-power-module-ipm/
10 Amp 400V DC Intelligent power module board has been designed using ON Semiconductors STK544UC62K. This Inverter IPM module includes the output stage of a 3-phase inverter, pre-drive circuits, bootstrap circuits, protection circuits, op-amp based current sense circuit, comparator circuit for fault/Over current output, Bus voltage output, onboard 5V DC regulator for op-amp circuit. This […]
3 Phase AC Motor Controller
https://www.electronics-lab.com/3-phase-ac-motor-controller/
This project made using MC3PHAC from NXP Semiconductor. The project generates 6 PWM signals for 3 Phase AC Motor controller. It’s very easy to make professional VFD combining with Intelligent Power Module (IPM) or 3 Phase IGBT/MOSFET with Gate driver. The board provides 6 PWM signals for the IPM or IGBT Inverter and also brake […]
2.5A 2Phase Micro-Stepping Stepper Motor Driver
https://www.electronics-lab.com/2-5a-2phase-micro-stepping-stepper-motor-driver/
2 Phase stepping motor driver is a tiny board based on STK682-010 hybrid IC from ON semiconductor and it can deliver current up to 2.5Amp and has supply up to 32V DC. It has multiple micro-stepping: Full step, 1/2th Step, 1/4th Step, 1/8th Step, 1/16th Step, 1/32th Step, 1/64th Step, 1/128th Step. PR1 trimmer potentiometer […]
16X2 LCD Shield with LMD18201 Motor Driver
https://www.electronics-lab.com/16x2-lcd-shield-lmd18201-motor-driver/
LCD is very important part of many DIY and industrial projects. The 16X2 LCD shield has been designed to develop LCD related projects using 28-40 Pin Pic development board or DSpic development board, along with LCD this shield includes LMD18201 DC Motor driver , 2 Trimmer potentiometer and 4 tact switches with jumpers. Jumpers […]
Inteligent Power Module (IPM) Board for Brushless Motors
https://www.electronics-lab.com/inteligent-power-module-ipm-board-brushless-motors/
Intelligent Power Module (IPM) board has been designed using FSBS5CH60 IC from Fairchild, which provides a fully-featured, high-performance inverter output stage for AC Induction, BLDC, and PMSM motors. These modules integrate optimized gate drive of the built-in IGBTs to minimize EMI and losses, while also providing multiple on-module protection features including under-voltage lockouts, over-current shutdown, […]
Sound to RC Servo Driver
https://www.electronics-lab.com/sound-rc-servo-driver/
This project is designed for Animatronics and Puppeteer applications, however it can be used in other applications like sound responsive toys, robots etc. Especially this project helps to move the jaw or mouth of animatronics creature. The project moves RC servo once receives any kind of sound. Rotation angle depends on sound level, more the […]
A DC Motor Controller with Control Leds
https://www.electronics-lab.com/dc-motor-controller-control-leds/
Boris Landoni writes about a new open source project a DC motor controller with control LEDs: The circuit board we are presenting this time is based on the dual-bridge driver L298N, in a traditionally mounted version in a Multiwatt container with 15 staggered pins; it has two terminal blocks for attaching to DC motors or the […]
400V – 5A Power Supply For Brushless Motor Drivers
https://www.electronics-lab.com/400v-5a-power-supply-brushless-motor-drivers/
Although the power supply design is specific to the Brushless Servo Drivers mainly for IPM Modules, the concepts and circuit design may be used for any power supply requires high voltage output up to 400V DC and 5 Amps. The power supply is an unregulated design with an option to allow connection to either 120V […]