IR Remote Controlled Motorized Potentiometer – Arduino Compatible
https://www.electronics-lab.com/ir-remote-controlled-motorized-potentiometer-arduino-compatible/
This is an Infrared Remote controlled motorized potentiometer controller. It’s an open-source project built on the Arduino platform and compatible with Arduino IDE for custom programming. The project consists ATMEGA328 microcontroller, IR sensor, L293D motor driver, ALPS Motorized potentiometer, a connector for Arduino programming, etc. The L293D H-bridge drives the potentiometer motor, 2 Parallel direction […]
DC Motor Speed, Direction and Brake Control with NRF24L01 RF Module – Arduino Compatible
https://www.electronics-lab.com/dc-motor-speed-direction-and-brake-control-with-nrf24l01-rf-module-arduino-compatible/
This is Arduino compatible hardware that can control a single DC motor speed, direction, and brake using an RF remote control. The project is based on an ATMEGA328 microcontroller, H-Bridge DC motor driver chip LM18201, NRF24L01 RF module, 5V Regulator, 3.3V regulator and other components. This board can drive a DC Motor up to 24V […]
Development board for Brushless Motor, DC Brushed Motor, AC Motors (Pre-Driver)
https://www.electronics-lab.com/development-board-for-brushless-motor-dc-brushed-motor-ac-motors-pre-driver/
The project described here is a pre-driver for brushless motors with a hall sensor. The board incorporates many features like current monitor, fault, speed control, direction control motor start/stop using tactile switches, various function LEDs, 6 PWM LEDs. By combining it with a hybrid IC or IPM module large size high voltage and high current […]
600W – 230VAC – High Voltage DC Motor Speed Controller – Heater Controller – Lamp/LED Dimmer
https://www.electronics-lab.com/600w-230vac-high-voltage-dc-motor-speed-controller-heater-controller-lamp-led-dimmer/
This is a very powerful DC Motor speed controller for DC motors up to 330V DC and current up to 2A. Basically, the project is a high voltage PWM source with adjustable frequency and adjustable PWM duty cycle range 0 to 99%. The board has been designed considering many applications and the circuit can be […]
600V – 30A IPM Module Carrier Board for Variable Frequency Drive (VFD)
https://www.electronics-lab.com/600v-30a-ipm-module-carrier-board-for-variable-frequency-drive-vfd/
This compact IPM module circuit provides a fully-featured, high-performance inverter output stage for AC Induction, BLDC, and PMSM motors. The circuit is based on FNA23060 chip which integrates the optimized gate drive of the built-in IGBTs to minimize EMI and losses, while also providing multiple on-module protection features: under-voltage lockouts, over-current shutdown, temperature sensing, and […]
Texas Instruments DRV8212 12V, 2A Low Voltage H-Bridge Motor Driver
https://www.electronics-lab.com/texas-instruments-drv8212-12v-2a-low-voltage-h-bridge-motor-driver/
Texas Instruments DRV8212 12V, 2A Low Voltage H-Bridge Motor Driver provides PWM, PH/EN, and half-bridge control interfaces and low-power sleep mode. The DRV8212 Motor Driver is integrated with four N-channel power FETs, a charge pump regulator, and protection circuitry. The triple charge pump architecture allows the device to operate down to 1.65V to accommodate 1.8V […]
Joystick Controlled 2 x RC Servo motors – Arduino Compatible
https://www.electronics-lab.com/joystick-controlled-2-x-rc-servo-motors-arduino-compatible/
This project enables easy control of 2 RC servo motors using a thumb joystick. This is an Arduino compatible project and it consists of a thumb joystick, ATMEGA328 microcontroller, filter capacitor on dc supply, and other components. The thumb joystick has 2 axes, X and Y. The joystick consists of 2 x 10K potentiometers. These […]
Valar Systems’ WiFi Stepper Motor Board with StallGuard Technology
https://www.electronics-lab.com/valar-systems-wifi-stepper-motor-board-with-stallguard-technology/
Controlling stepper motors over a WiFI network opens up the possibilities for the integration of wireless and automation functions to your motor applications. We saw a WiFi Stepper board by Good Robotics in January 2019, it featured control over Wifi and enabled an IoT interface for any stepper motor all the way up to 85V […]
MP6540H/MP6540HA are three-phase brushless DC motor drivers
https://www.electronics-lab.com/mp6540h-mp6540ha-are-three-phase-brushless-dc-motor-drivers/
MPS’ 50 V, 5 A and 6 A, three-phase power stage drivers offer PWM and enable inputs The MP6540H and MP6540HA from Monolithic Power Systems are three-phase brushless DC motor drivers. These devices integrate three half-bridges consisting of six N-channel power MOSFETs, pre-drivers, gate drive power supplies, and current-sense amplifiers. The MP6540H has enable (EN) […]
15V to 60V – Three-Phase Brushless DC Motor Pre-Driver
https://www.electronics-lab.com/15v-to-60v-three-phase-brushless-dc-motor-pre-driver/
The project presented here is a three-phase BLDC motor pre-driver. The project consists of 3x half-bridge IR2101 driver IC and 6 channel high current N-MOSFETS. The project can be configured as 3 independent half-bridges H-bridge for a brushed DC motor, or a single high current brushless motor driver. The rotor position can be detected using […]