BLDC Motor and DC Brushed Motor Driver
https://www.electronics-lab.com/bldc-motor-and-dc-brushed-motor-driver/
This BLDC motor driver board is equipped with a smart IFX007T half-bridge. The BLDC motor control project is capable to drive one BLDC motor. Alternatively, it can be used to drive one or two bi-directional DC motors (H-Bridge configuration, cascaded to support the second motor) or up to three uni-directional DC motors (half-bridge configuration). The […]
Diodes Incorporated AP3128 PWM Controller
https://www.electronics-lab.com/diodes-incorporated-ap3128-pwm-controller/
Diodes Incorporated AP3128 PWM Controller is a peak-current control and multi-mode (QR+CCM) PWM controller. This controller is optimized for high performance, low standby power, and cost-effective offline flyback converters. The AP3128 is designed to enter burst mode at no-load/light-load and minimizes standby power consumption. This controller features a 105kHz maximum switching frequency that clamps the QR […]
8A Brushed DC Motor Driver with Adjustable Constant Current, Direction Control, Brake Control, Speed Control
https://www.electronics-lab.com/8a-brushed-dc-motor-driver-with-adjustable-constant-current-direction-control-brake-control-speed-control/
This is a very powerful brushed DC motor drive system in a small package with a few key features like adjustable constant current control, direction control, brake controls, Alert output, PWM for speed control etc. The project was built using a TB67H303HG chip which is a full-bridge driver IC for DC motor adopting MOS at […]
Diodes Incorporated AP3304 Multi-Mode PWM Controller
https://www.electronics-lab.com/diodes-incorporated-ap3304-multi-mode-pwm-controller/
Diodes Incorporated AP3304 Multi-Mode PWM Controller is optimized for high-performance, low standby power, and cost-effective offline flyback converters. This PWM controller features peak-current control, multi-mode control with CCM+QR, a low start-up current of 1μA, and a soft start during the start-up process. The AP3304 PWM controller at light load operates in burst mode with a […]
Phase-Shifted Full-Bridge PWM Controller Module – LM5046 Breakout Board
https://www.electronics-lab.com/phase-shifted-full-bridge-pwm-controller-module-lm5046-breakout-board/
This is a Phase-Shifted Full-Bridge PWM LM5046 carrier board that contains all of the features necessary to implement a phase-shifted full-bridge topology power converter. All inputs and outputs pins are accessible using the header connector. High efficiency DC-DC converter can be created using LM5046 carrier board + External H-Bridge and Transformer. Refer to the datasheet […]
Radio Remote Control LED Dimmer Using NRF24L01 – Arduino Compatible
https://www.electronics-lab.com/radio-remote-control-led-dimmer-using-nrf24l01-arduino-compatible/
This is an easy-to-make LED dimmer using RF remote control. The project is capable of driving a load up to 24W (2A X 12V LED). Any 12V single or 12V LED strip can be used. This is an open-source Arduino compatible hardware that has Atmega328 microcontroller, Potentiometer, MOSFET, 5V Regulator, 3.3V Regulator, NRF24L01 Radio modules, […]
12W Constant-Current LED Driver with PWM Dimming – 12V DC@1A Input
https://www.electronics-lab.com/12w-constant-current-led-driver-with-pwm-dimming-12v-dc1a-input/
This is a high-performance, adjustable constant current, and PWM dimmer project. It provides accurate output constant current and PWM control. The circuit regulates the current flowing through a LED/LED array to maintain the desired level of light output. The board consists of CAT4101 LED driver chip and LTC6992-1 PWM generator chip. 12W Constant-Current LED Driver […]
230V AC Input – 12V Output DC Converter, Non-Isolated Buck Converter
https://www.electronics-lab.com/230v-ac-input-12v-output-dc-converter-non-isolated-buck-converter/
The project described here outputs 12V DC voltage from the input of 230V AC. The output current is up to 100mA. The project is based on BM2P129TF chip which is PWM method DC/DC converter with a built-in 650V MOSFET. BM2P129TF contributes to low power consumption by built-in a 650V starting circuit. Built-in current detection resistor […]
Infineon Technologies XENSIV™ PAS CO2 sensor
https://www.electronics-lab.com/infineon-technologies-xensiv-pas-co2-sensor/
High performance in a small size – disruptive CO2 PAS sensor Increasingly efficient building insulation can help to mitigate the effects of climate change, but heavily insulated buildings are not always good for human health. Poor ventilation can result in lower oxygen levels and a build-up of carbon dioxide (CO2). Even moderate levels of CO2 can […]
Development board for Brushless Motor, DC Brushed Motor, AC Motors (Pre-Driver)
https://www.electronics-lab.com/development-board-for-brushless-motor-dc-brushed-motor-ac-motors-pre-driver/
The project described here is a pre-driver for brushless motors with a hall sensor. The board incorporates many features like current monitor, fault, speed control, direction control motor start/stop using tactile switches, various function LEDs, 6 PWM LEDs. By combining it with a hybrid IC or IPM module large size high voltage and high current […]