Attiny85 8-pin Arduino Programing Shield
https://www.electronics-lab.com/attiny85-8-pin-arduino-programing-shield/
This Arduino shield transforms your Arduino UNO into an ISP-Programmer for the ATtiny85 microcontroller. The board simplifies the Boot-loader burning on the ATtiny85 chip. It consists of an 8-pin DIP socket to insert the new ATtiny85 chip, C1 decoupling capacitor, and C2 capacitor is provided to avoid the Arduino UNO from being auto-reset when we […]
Expansion Shield – Breakout Board for Arduino Nano
https://www.electronics-lab.com/expansion-shield-breakout-board-for-arduino-nano/
If you need to interface many devices and sensors to Arduino Nano, then, this project is for you. This is a Nano expansion I/O shield (breakout board) for the Arduino Nano. The board facilitates the easy connection between Arduino Nano and other devices. Each Arduino (I/O) Pin including the 5V DC and GND pins are […]
8 Channel Infra-Red Remote-Control Arduino Shield Using ULN2803
https://www.electronics-lab.com/8-channel-infra-red-remote-control-arduino-shield-using-uln2803/
This is an 8 channel infra-red remote-control Arduino shield that can drive 8 high current loads such as LEDs, solenoids, multiple toy DC Motors, dual unipolar stepper motor, filament lamps, etc. Each channel consists of two parallel NPN transistors with freewheel diodes which are important to drive inductive loads like motors. The shield consists of […]
Type K Thermocouple Sensor Amplifier Arduino Shield
https://www.electronics-lab.com/type-k-thermocouple-sensor-amplifier-arduino-shield/
This is a Type K Thermocouple Sensor Amplifier Arduino Shield that enables an Arduino board to acquire temperatures from a thermocouple of type K. The shield works with a single supply and takes 5V DC from the Arduino board, the output of the circuit is 0 to 4V DC for 0-degree centigrade to 400C. The […]
Optically Isolated Bidirectional I2C Shield For Arduino
https://www.electronics-lab.com/optically-isolated-bidirectional-i2c-shield-for-arduino/
Optically isolator Arduino Shield has been designed to provide optically isolated I2C communication between Arduino and any other device or sensors that works with I2C protocols. I have used the ISO1540 Low-Power Bidirectional I2C Isolator IC from Texas Instruments to build this project, and the device is compatible with I2C interfaces. These devices have logic […]
8 Channel Inductive Load Driver Arduino Shield
https://www.electronics-lab.com/8-channel-inductive-load-driver-arduino-shield/
The 8 Channel Driver Arduino UNO Shield is designed to enable users to switch inductive loads for up to 800mA each channel and up to 24V DC with no heat-sink needed. It is ideal for such applications as driving 2x unipolar stepper motors, solenoids, relays, and small DC motors. It uses 2x DRV8803 Chip from […]
ShielDIY Do-It-Yourself Custom Shielding Cabinets
https://www.electronics-lab.com/shieldiy-do-it-yourself-custom-shielding-cabinets/
Würth Elektronik’s ShielDIY kit is a fast prototyping solution for board-level shielding cabinets Würth Elektronik has created a do-it-yourself custom shielding cabinet kit, the ShielDIY. The ShielDIY kit is a fast prototyping solution for board level shielding cabinets. The kit is made up of nickel silver sheet with a thickness of 0.2 mm. The sheets […]
2.7A PWM Valve/Solenoid Driver Arduino Nano Shield
https://www.electronics-lab.com/2-7a-pwm-valve-solenoid-driver-arduino-nano-shield/
This Arduino shield helps to drive various loads like a solenoid, valve, motor, inductive actuator, heater, and bulb. A wide supply range 8V-60V and a load current of 2.7A allows it to be used with a variety of actuators. The board can be used as a stand-alone driver or it can be controlled by Arduino […]
Sound Sensor with onboard Relay Arduino Nano Shield
https://www.electronics-lab.com/sound-sensor-onboard-relay-arduino-nano-shield/
This sound sensor with Relay driver shield for Arduino Nano can be used to develop sound-activated ON/OFF switch or other projects that require sound senor. LM358 op-amp is used as the amplifier, 1st op-amp amplifies the microphone signal, and 2nd op-amp works as a half-bridge rectifier that converts AC signal into a DC voltage. This […]
RS485 Shield For Arduino Nano
https://www.electronics-lab.com/rs485-shield-arduino-nano/
Arduino Nano RS485 shield will help you to transmit and receive serial data using the twisted pair RS485 network. The module provides half-duplex communication. LED D1 indicates receive data, D2 Transmit LED, J1 jumper is optional and not in use in this application. DI/RE connected to D2 of Arduino digital pin which enables Receiver Output […]