MP6612 – 45V, 5A, H-Bridge DC Motor Driver with Current Sense and IN1/IN2 Logic Inputs
https://www.electronics-lab.com/mp6612-45v-5a-h-bridge-dc-motor-driver-with-current-sense-and-in1-in2-logic-inputs/
The MP6612 from Monolithic Power Systems is a Half-Bridge DC Motor Driver that is used for driving reversible motors. It requires an input voltage of 4-45 V for operation and has an output current of up to 5 A. The motor driver consists of four N-channel power MOSFETs and an internal charge pump that generates […]
Texas Instruments DRV8251 4.1A Brushed DC Motor Driver
https://www.electronics-lab.com/texas-instruments-drv8251-4-1a-brushed-dc-motor-driver/
Texas Instruments DRV8251 4.1A Brushed DC Motor Driver is an integrated motor driver with N-channel H-bridge, charge pump, current regulation, and protection circuitry. The charge pump improves efficiency by supporting N-channel MOSFET half-bridges and 100% duty cycle driving. The DRV8251 implements a current regulation feature by comparing the analog input VREF and the voltage across […]
Low-Cost DC Motor Direction Controller with Fast Brake using 2 Relays
https://www.electronics-lab.com/low-cost-dc-motor-direction-controller-with-fast-brake-using-2-relays/
The project presented here is a low-cost easy to use DC brushed motor direction controller with fast-brake, the project was built using two 12V Relays, 2 x BJT transistors, and 2 x tactile switches. The two LEDs are provided to display the motor direction, 2 tactile switch controls the direction of the motor. Low-Cost DC […]
BLDC Motor and DC Brushed Motor Driver
https://www.electronics-lab.com/bldc-motor-and-dc-brushed-motor-driver/
This BLDC motor driver board is equipped with a smart IFX007T half-bridge. The BLDC motor control project is capable to drive one BLDC motor. Alternatively, it can be used to drive one or two bi-directional DC motors (H-Bridge configuration, cascaded to support the second motor) or up to three uni-directional DC motors (half-bridge configuration). The […]
Bidirectional Speed Control for DC Motors
https://www.electronics-lab.com/bidirectional-speed-control-for-dc-motors/
This is a very simple bidirectional speed control of a small DC brushed motor. The project is built using power OPAMP TCA0372 which can drive a load up to 1A. Connecting a small DC motor and trimmer pot will control the motor forward/reverse operation along with speed control. A Trimmer potentiometer is provided to set […]
CN0531 – Programmable 20-Bit, Linear, Precision, Bipolar ± 5V DC Voltage Source
https://www.electronics-lab.com/cn0531-programmable-20-bit-linear-precision-bipolar-%c2%b1-5v-dc-voltage-source/
Precision dc voltages are a critical component of scientific instrumentation and measurement equipment, automated test equipment, factory automation and control, chemical analysis, and many other high precision applications. The most demanding applications require single digit, part per million temperature drift, subppm linearity, and low, predictable noise performance. The circuit shown in Figure 1 is a […]
12VDC to 220-380VDC Converter
https://www.electronics-lab.com/12vdc-to-220-380vdc-converter/
When powering many appliances from a sine wave inverter, the HV DC is converted to AC only to be rectified back to DC in the appliance. This inverter eliminates the SPWM stage and outputs DC only. This DC can be used to power appliances, or as a HV DC source for your SPWM, variable frequency […]
High Voltage DC Power Supply for intelligent Power Modules
https://www.electronics-lab.com/high-voltage-dc-power-supply-for-intelligent-power-modules/
Although this power supply design is specific to the Intelligent Power Modules (IPM), the concepts and circuit design may be used for any power supply that requires high voltage output up to 400V DC and 6 A. It is an unregulated power supply, DC output is dependent on AC input. The circuitry includes a passive […]
Sensorless FOC 3 Phase Low Power Brushless BLDC Motor Driver
https://www.electronics-lab.com/sensorless-foc-3-phase-low-power-brushless-bldc-motor-driver/
Driving a 3-phase brushless DC motor is very easy with this project. It is a simple and easy-to-build project that requires only a few external components. The circuit is based on AMT49400 IC which is an advanced 3-phase, Sensorless, brushless DC (BLDC) motor driver with integrated power MOSFETs. The chip includes the field-oriented control (FOC) […]
Free Elektor Project: Inrush Current Limiter (Soft Starter) for AC and DC Loads
https://www.electronics-lab.com/free-elektor-project-inrush-current-limiter-soft-starter-for-ac-and-dc-loads/
Inrush current/Switch-ON surge is the maximal instantaneous input current drawn by an electrical device when first turned on. Inrush current is much higher than the load’s steady-state current and that’s the source of many problems such as fuse blowing up, load failure, load’s lifetime reduction, sparks at the switch contacts … etc. The figure below […]