New Sensor Board from Parametric Circuits provides a whole new level of Integration
https://www.electronics-lab.com/new-sensor-board-parametric-circuits-provides-whole-new-level-integration/
Sensor boards are manufactured to provide engineers with the ideal platform for developing projects and designs that detect or measure temperature, pressure, humidity, color, motion, and even physical location. They offer necessary support circuitry that allows for the full utilization of sensors for demonstration and evaluation. While there’s been a wide range of available sensor […]
ATtiny10 Development Board with USB-C and Micro USB
https://www.electronics-lab.com/attiny10-development-board-usb-c-micro-usb/
If you like using the simplest possible chip for each of your applications, then the ATtiny10 development board will strongly appeal to you. The ATtiny10 development board from Bobricius is a low-power high-performance 6-pin processor equipped with both USB-C and Micro-USB for powering purposes only. True to its name “tiny”, the chip is about the […]
Elektor Article: LED Booster for Microcontrollers
https://www.electronics-lab.com/elektor-article-led-booster-microcontrollers/
There’s many a time when you want to connect a white LED to a microcontroller operating from a 3 V supply voltage. Unfortunately, this doesn’t work and your nice white LED only lights up feebly or not at all. Why does it work perfectly with red and green LEDs, but not with white? A bit […]
Ohm’s Law
https://www.electronics-lab.com/article/ohms-law/
Introduction The fundamental relation between the current, voltage, and resistance is known as Ohm’s law and is probably the most famous and elementary physical law of electronics. It is in 1827 when the German physicist Georg Simon Ohm publishes for the first time in the book “Die galvanische Kette, mathematisch bearbeitet” (in English: The mathematical […]
DipDuino – is an Arduino in 0.3in DIP form
https://www.electronics-lab.com/dipduino-arduino-0-3in-dip-form/
DipDuino is an Arduino in 0.3in DIP form. It runs the Atmega328P. Uses an onboard CP2104 to program itself and comes pre-programmed with Arduino Bootloader. Will act as a Arduino Pro or Pro Mini. Available in Tindie Store. The DipDuino is a FULL ARDUINO (Minus the A6 & A7 pins). Comes in 5v and 3.3v […]
TinySolder – T12 Soldering Station based on ATtiny13a
https://www.electronics-lab.com/tinysolder-t12-soldering-station-based-attiny13a/
TinySolder is a simple T12 Quick Heating Soldering Station based on the ATtiny13a featuring in 700 bytes of code: Temperature measurement of the tip Direct control of the heater Temperature control via potentiometer Handle movement detection (by checking ball switch) Time driven sleep/power off mode if iron is unused (movement detection) TinySolder – T12 Soldering […]
Broadcom AFBR-S4N33C013 is a silicon photo multiplier
https://www.electronics-lab.com/broadcom-afbr-s4n33c013-silicon-photo-multiplier/
The Broadcom® AFBR-S4N33C013 is a single silicon photomultiplier (SiPM) used for ultra-sensitive precision measurement of single photons. The active area is 3.0 × 3.0 mm2. The high packing density of the single chips is achieved using through-silicon-via (TSV) technology and a chip-sized package (CSP). Larger areas can be covered by tiling multiple AFBR-S4N33C013 CSPs almost […]
How to use PICKit+ with MPLAB-X IDE
https://www.electronics-lab.com/use-pickit-mplab-x-ide/
PICKit+ recently announced that it is now possible to Program Microchip PICs from MPLAB-X using PICkit2 programmer and it’s even possible for those PICs that MPLAB-X programmer operations do not support. The challenge There are many PIC microcontrollers that currently not supported by MPLAB-X or MPLAB-IPE. This typically includes: 16(L)F15xxx 16(L)F18xxx 16(L)F19xxx 18(L)FxxK40 18(L)FxxK42 18(L)FxxK83 […]
Cricket ONE is an Arduino compatible board in Raspberry Pi form factor
https://www.electronics-lab.com/cricket-one-arduino-compatible-board-raspberry-pi-form-factor/
The Cricket ONE is the first in a series of small microcontroller boards using the familiar form factor of the Raspberry Pi Zero series of single-board computers. Featuring an ATMEGA328PB and CH340C USB to UART converter, this board is Arduino IDE compatible and includes all of the features of the newer ATMEGA328PB. Basic Specs: ATMEGA328PB […]
Toradex i.MX 8X-based System on Modules gain AWS certification and support for Torizon embedded Linux
https://www.electronics-lab.com/toradex-mx-8x-based-system-modules-gain-aws-certification-support-torizon-embedded-linux/
Toradex is now bringing Torizon, its easy-to-use industrial Linux software platform, to its System on Modules (SoMs) based on the i.MX 8X applications processors from NXP®. Toradex offers the i.MX 8X-based SoMs in two form factors: the small Colibri iMX8X and the powerful Apalis iMX8X, with optional ECC memory. Toradex was among the first few partners to be part […]