UP/DOWN counter with memory using PIC16F88
https://www.electronics-lab.com/updown-counter-with-memory/
Here is an up-down counter based on PIC16F88 and 7-segment display. The counter is using SMD components and features a RS-232 interface. This is a simple digital counter with a serial rs-232 and a 7 segment display, i started this project to count items on some shelfs, but it can be used for anything, it […]
-5V @100mA Switched Capacitor Converter
https://www.electronics-lab.com/project/5v-100ma-switched-capacitor-converter/
The circuit diagram presented here is about a negative voltage regulator. It is based on LT1054, which is a switched capacitor voltage converter with regulator from Texas instrument. This device has many advantages over other previously available switched capacitor voltage converters. It provides higher current and has lower voltage losses. Features: Input Voltage: 3.5VDC to […]
Choose the right step-up/down voltage regulator for portable applications
https://www.electronics-lab.com/choose-the-right-step-updown-voltage-regulator-for-portable-applications/
Reno Rossetti & Inyong Kim discuss about the power needs on portable devices and help us choose the right regulator. A popular power source for portable devices is a single lithium-ion cell with 4.2V at full charge and 2.8V at end of discharge. However, some functions within portable electronics, such as a SIM card and […]
LTC7813 – Low IQ, 60V Synchronous Boost+Buck Controller
https://www.electronics-lab.com/ltc7813-low-iq-60v-synchronous-boostbuck-controller/
Linear Technology Corporation introduces the LTC7813, a dual output (boost + buck), low quiescent current synchronous DC/DC controller. When cascaded, its independent step-up (boost) and step-down (buck) controllers regulate the output voltage from an input voltage that can be above, below, or equal to the output voltage, including during an automotive load dump or cold […]
Open-source microprocessor
https://www.electronics-lab.com/open-source-microprocessor/
Fabio Bergamin @ phys.org writes about PULPino which is an open source processor to be used on wearables and IoT. In future, it will be easier and cheaper for developers at universities and SMEs to build wearable microelectronic devices and chips for the internet of things, thanks to the PULPino open-source processor, which has been developed at […]
Nanocounter: Frequency Counter with an Android Interface
https://www.electronics-lab.com/nanocounter-frequency-counter-with-an-android-interface/
Andy published his accurate and open source frequency counter that uses an Android phone as a display. It’s based on a high accuracy temperature compensated crystal oscillator (TCXO) fed into a phase locked loop (PLL) to create a high frequency reference clock. The reference clock along with the input signal is processed by a Xilinx […]
1″ 100W Hot-Plate for SMT Reflow
https://www.electronics-lab.com/1%e2%80%b3-100w-hot-plate-for-smt-reflow/
This is a small hot-plate for SMT reflow soldering build upon an Arduino Pro and controlled using PWM and high side power MOSFETs. Black Mesa Labs has been using a $20 hot plate for a year now for soldering QFN ICs to PCBs. Only issue so far has been the size ( 10″x10″x3″ ) and […]
VoCore: A Cheap And Coin-sized Linux Computer With Wi-Fi
https://www.electronics-lab.com/vocore-a-cheap-and-coin-sized-linux-computer-with-wi-fi/
VoCore is an open source hardware that runs OpenWRT Linux. This tiny computer comes with Wi-Fi, USB, 20+ GPIOs that will help you to embed it on your projects. With each passing day, mini computer boards are getting more and more popular. Single board computers like Raspberry Pi, CHIP, OrangePi etc. are being endorsed by […]
9V to 1kV DC/DC converter
https://www.electronics-lab.com/9v-to-1kv-dcdc-converter/
Bob tipped us with his latest project, it’s a 9V to 1kV DC-DC converter using CD4011 IC to produce a square wave and a IRF530 transistor to drive the transformer. Finally, I have made a new high voltage supply based on an inverter transformer and voltage doubler. It seems to be ok for this job, […]
Dual DC Motor driver using two L293D
https://www.electronics-lab.com/dual-dc-motor-driver-using-two-l293d/
Dual DC Motor driver using two L293D IC. The L293D device is quadruple high-current half-H driver. The 293D is designed to provide bidirectional drive current up to 600mA a voltage from 5V to 36V. It provides 600mA +600mA on each channel suitable for mini hobby robots. The board been designed mainly for small size robot, […]