Getting Started With BTE13-010 – Arduino Mini Clone
https://www.electronics-lab.com/getting-started-bte13-010-arduino-mini-clone/
by techrm @ instructables.com This is a simple guide that will teach you how to get started with this cheap Arduino mini clone, covering all the steps one should do to make it work. Getting Started With BTE13-010 – Arduino Mini Clone – [Link]
Arduino 433Mhz RF Wireless Data Transfer
https://www.electronics-lab.com/arduino-433mhz-rf-wireless-data-transfer-2/
runtimeprojects.com has a tutorial on how to use 433Mhz modules to communicate between 2 Arduinos. The most practical and cool way of sharing data from 1 Arduino to another is by far using a radio transmitter and receiver. The simplest form of wireless transmission (I could find) is the 433Mhz ASK modules. They come in […]
How to Make an Arduino Capacitance Meter
https://www.electronics-lab.com/make-arduino-capacitance-meter/
circuitbasics.com has a tutorial on how to measure capacitance using arduino. With all the different ways capacitors are labeled, figuring out the values of your capacitors can be challenging. Especially if you don’t have a digital multi-meter to test them. In this tutorial, I’ll show you how to build three different capacitance meters using an Arduino and a couple […]
Start with Arduino in 15 minutes
https://www.electronics-lab.com/start-arduino-15-minutes/
The ultimate Arduino tutorial for beginners. Learn what Arduino is, how to choose an Arduino, then build a simple data logger, LED dimmer and motor speed controller. Start with Arduino in 15 minutes – [Link]
Arduino-Programmable ESP32 Development Board
https://www.electronics-lab.com/arduino-programmable-esp32-development-board/
Ezsbc, an American embedded control solutions retailer, had produced a new development board that simplifies working with ESP32 module and makes it programmable via USB using the Arduino IDE. The ESP32 is a low cost, ultra low power microcontroller with integrated Wi-Fi & dual-mode Bluetooth, which employs a dual-core Tensilica Xtensa LX6 microprocessor. ESP32 is […]
Premier Farnell partners with Intel on IoT
https://www.electronics-lab.com/premier-farnell-partners-intel-iot/
Farnell element14’s tinyTILE is an Intel Curie module based board created by the distributor in partnership with Intel. by Julien Happich @ edn-europe.com: Measuring only 35x26mm, the tinyTILE has been specifically designed for use in wearable and IoT designs for consumer and industrial edge products. It runs a software platform created specifically for the Intel […]
Arduino Interrupts Tutorial
https://www.electronics-lab.com/arduino-interrupts-tutorial/
In this video educ8s.tv is going to show us how to use interrupts with Arduino, an advanced but extremely useful feature of the Arduino. But what is an interrupt? Most microprocessors have interrupts. Interrupts let you respond to external events while doing something else. Suppose you are sitting at home waiting for the new ESP32 board, […]
Simple 3 phase Arduino energy meter
https://www.electronics-lab.com/simple-3-phase-arduino-energy-meter/
Simple 3 Phase Arduino energy meter from The DIY Life: Again, with this meter I was going for simplicity. Sure, for perfectly accurate measurements you need to measure both the supply current and voltage but for this application and in the interests of keeping the energy meter simple and safe – only requiring a non-contact […]
The New Arduino 101 (Genuino 101) – Unboxing, Set Up, and Comparing it to the Arduino Uno
https://www.electronics-lab.com/new-arduino-101-genuino-101-unboxing-set-comparing-arduino-uno/
Arduino’s newest board, the Arduino 101 is finally here… It has an Intel Curie processor, and an on-board gyroscope, accelerometer, and Bluetooth. Let’s see how it stacks up to the Uno, and find out what each of the components on the board do. At the end of the video, I go through setting it up […]
Hack Your Car With Macchina M2
https://www.electronics-lab.com/hack-car-macchina-m2/
Car hacking applications have been growing during the last few years, making it faster and cheaper to get into automotive tinkering. A new device was launched recently on kickstarter called M2 by Macchina. M2 is an open-source, versatile development platform which can be wired under the hood for a more permanent installation or plugged into the […]