Brushed DC Motor Controller Using Rotary Encoder – Arduino Compatible
https://www.electronics-lab.com/project/brushed-dc-motor-controller-using-rotary-encoder-arduino-compatible/
This DC Motor controller provides direction and speed control of brushed DC Motor using Rotary Encoder. This is Arduino compatible hardware that consists of LMD18201 DC motor driver chip, Atmega328 microcontroller, Rotary Encoder, L317 regulator, and other components. Hardware offers easy control of brushed DC motor up to 3A with speed, direction, and brake control. […]
Carrier Board for Advanced Phase-Shift PWM Controller UCC3895
https://www.electronics-lab.com/project/carrier-board-for-advanced-phase-shift-pwm-controller-ucc3895/
This is a Phase-Shifted Full-Bridge PWM UCC3895 carrier board that contains all of the features necessary to implement a phase-shifted full-bridge topology power converter. All inputs and outputs pins are accessible using a header connector. A highly-efficient DC-DC converter can be created using this carrier board + External H-Bridge and Transformer. Refer to the datasheet […]
IR Remote Controlled Motorized Potentiometer – Arduino Compatible
https://www.electronics-lab.com/project/ir-remote-controlled-motorized-potentiometer-arduino-compatible/
This is an Infrared Remote controlled motorized potentiometer controller. It’s an open-source project built on the Arduino platform and compatible with Arduino IDE for custom programming. The project consists ATMEGA328 microcontroller, IR sensor, L293D motor driver, ALPS Motorized potentiometer, a connector for Arduino programming, etc. The L293D H-bridge drives the potentiometer motor, 2 Parallel direction […]
DC Motor Speed, Direction and Brake Control with NRF24L01 RF Module – Arduino Compatible
https://www.electronics-lab.com/project/dc-motor-speed-direction-and-brake-control-with-nrf24l01-rf-module-arduino-compatible/
This is Arduino compatible hardware that can control a single DC motor speed, direction, and brake using an RF remote control. The project is based on an ATMEGA328 microcontroller, H-Bridge DC motor driver chip LM18201, NRF24L01 RF module, 5V Regulator, 3.3V regulator and other components. This board can drive a DC Motor up to 24V […]
15V to 60V – Three-Phase Brushless DC Motor Pre-Driver
https://www.electronics-lab.com/project/15v-to-60v-three-phase-brushless-dc-motor-pre-driver/
The project presented here is a three-phase BLDC motor pre-driver. The project consists of 3x half-bridge IR2101 driver IC and 6 channel high current N-MOSFETS. The project can be configured as 3 independent half-bridges H-bridge for a brushed DC motor, or a single high current brushless motor driver. The rotor position can be detected using […]
Motorized Slide Potentiometer Driver
https://www.electronics-lab.com/project/motorized-slide-potentiometer-driver/
This motorized slide potentiometer is used in lighting and Audio/Video equipment or other similar application. It is a simple solution to control a motorized slide potentiometer using two tactile switches or a microcontroller interface. The project includes bidirectional motor driver L293DD H-Bridge chip, LM555 timer IC to generate the PWM pulse for speed control and […]
10A 400V DC Intelligent Power Module (IPM)
https://www.electronics-lab.com/project/10a-400v-dc-intelligent-power-module-ipm/
This 10A -400V DC Intelligent power module board has been designed using ON Semiconductors STK544UC62K. This Inverter IPM module includes the output stage of a 3-phase inverter, pre-drive circuits, bootstrap circuits, protection circuits, op-amp based current sense circuit, comparator circuit for fault/Over current output, Bus voltage output, onboard 5V DC regulator for op-amp circuit. The […]
Intelligent Power Module (IPM) Board for Brushless Motors
https://www.electronics-lab.com/project/inteligent-power-module-ipm-board-brushless-motors/
Intelligent Power Module (IPM) board has been designed using FSBS5CH60 IC from Fairchild, which provides a fully-featured, high-performance inverter output stage for AC Induction, BLDC, and PMSM motors. These modules integrate optimized gate drive of the built-in IGBTs to minimize EMI and losses, while also providing multiple on-module protection features including under-voltage lockouts, over-current shutdown, […]
5 Amp H-Bridge DC Motor Driver using MC33886
https://www.electronics-lab.com/project/5-amp-h-bridge-dc-motor-driver-using-mc33886/
This tiny module has been designed to be used in Robotics, Power tools, automotive applications etc. The module is based on MC33886 from NXP. The MC33886 is a monolithic power IC comprising control logic, charge pump, gate drive, and low RDS(ON)MOSFET, H-Bridge output circuitry in a small surface-mount package. MC33886 is a monolithic H-Bridge ideal […]